New products

Mini computer based on the RP2350B microcontroller, equipped with a DVI output, two USB Type-A Host ports, WiFi connectivity, a microSD card reader and an audio system. The board provides 16 MB of Flash memory, 8 MB of PSRAM and a GPIO connector, and can be programmed using CircuitPython, Arduino or Pico SDK. Adafruit 6200

28BYJ-48 stepper motor powered by 12 V DC and equipped with a 1:64 reduction gearbox. The motor provides a step angle of 5.625° before gear reduction and an in-traction torque exceeding 34.3 mN·m at 120 Hz. It can be used in small mechanisms requiring controlled rotary motion. Elecrow 28BYJ-48

5 MP color camera module with autofocus, designed for use with microcontrollers via the SPI interface. The camera captures JPEG images at resolutions up to 2592 x 1944 px, supports 3.3 V / 5 V power supply and features an 8 MB frame buffer. It is compatible with platforms including Arduino, ESP32, ESP8266, STM32, Raspberry Pi Pico and Nordic. Arducam B040101

Nordic Semiconductor development kit featuring the nRF7002 WiFi 6 companion IC and a dual-core nRF5340 SoC operating as the host processor. The board supports WiFi, Bluetooth Low Energy, Bluetooth Mesh, NFC, Thread and Zigbee, and includes an onboard SEGGER J-Link programmer/debugger. The Arduino Uno Rev3-compatible form factor facilitates expansion of IoT prototypes. Nordic Semiconductor nRF7002-DK

MAX31865-based module designed for use with PT1000 RTD temperature sensors in 2-, 3- or 4-wire configurations. SPI communication enables connection to microcontrollers, while the 3.3 V regulator and logic level shifting provide compatibility with 5 V systems. PT1000 sensor is not included. Adafruit 3648

Automatic discharger designed to reduce the voltage of 2S-6S LiPo batteries to a suitable storage level. The circuit automatically detects the number of cells, stops discharging at 3.85 V ± 0.08 V per cell and uses a temperature sensor and heatsink for temperature management during operation. VIFLY StoreSafe XT30

LED lighting system designed for the DJI Neo, equipped with 86 LEDs arranged around the drone body. The system offers seven colors and seven lighting effects, while two built-in 150 mAh batteries provide at least 50 minutes of operation in steady-on mode. VIFLY NeoHalo LED Strip for DJI Neo.

Illuminated propeller duct guards designed for the DJI Avata 2, combining additional protection with multicolor LED lighting. The system uses 130 LEDs, offers seven colors and seven lighting effects, while the built-in batteries provide at least 50 minutes of operation in steady-on mode. VIFLY LED Duct Guards for DJI Avata 2

Lighting kit designed for the DJI Avata 2, consisting of a front light with Cree LEDs and two downward-facing lights. The front light provides a luminous flux of up to 400 lm, while the bottom lights illuminate the area beneath the drone to support the positioning system in dark environments. The total weight of the kit is 50 g. VIFLY Tactical Light for DJI Avata 2

Series charging board designed for charging from 1 to 6 1S LiPo batteries using a standard charger supporting multi-cell battery packs. The rotary switch allows the number of connected batteries to be selected, while the built-in fuse provides additional protection during charging. Version equipped with BT2.0 & PH2.0 connectors. VIFLY 1S Series Charging Board

Compact module designed for switching video between two FPV cameras in racing drones and RC airplanes. Control can be performed using a PWM signal or receivers supporting SBUS, IBUS and DSMX, without requiring configuration in Betaflight. VIFLY Cam Switcher

Compact anti-collision light equipped with six Cree LEDs in four colors: white, red, green and blue. The luminous flux reaches 1000 lm, while the manufacturer-declared visibility range exceeds 3 miles. The built-in 180 mAh battery provides up to 4 hours of operation in quick strobe mode. VIFLY Strobe Platinum

Compact anti-collision light designed to increase drone visibility during flight, equipped with white, red and green LEDs. It offers multiple lighting modes, a manufacturer-declared visibility range of over 3 miles and an operating time of up to 4 hours in strobe mode. The built-in 160 mAh battery is charged via USB Type-C. VIFLY Strobe

Independent power module designed for GPS receivers used in FPV drones, allowing satellites to be acquired without powering up the flight controller or video transmission system. It supports 3.3 V and 5 V GPS receivers and provides an output current of up to 80 mA. The built-in locator function with a buzzer volume of up to 90 dB helps locate the model after loss of main power. VIFLY GPS-mate

Compact locator buzzer designed for small FPV drones and RC models, equipped with its own 40 mAh LiPo battery. The audible signal reaches a volume of up to 100 dB, while the operating time after loss of main power is up to 7 hours. VIFLY Finder Mini

Automatic discharger designed to reduce the voltage of 2S-6S LiPo batteries to a suitable storage level. The device automatically detects the number of cells, stops discharging at 3.85 V ± 0.08 V per cell, and uses a temperature sensor and heatsink to control temperature during operation. VIFLY StoreSafe XT60.

Electronic protection device designed to protect RC systems and drone electronics during initial power-up, diagnostics and power system testing. When a short circuit or the selected 1 A or 2 A current threshold is exceeded, the device cuts off the current flow, reducing the risk of component damage. VIFLY ShortSaver V2

Wireless locator buzzer using a motion sensor to detect when a drone stops moving or crashes. The built-in 80 mAh LiPo battery enables independent operation, while the audible signal reaches up to 105 dB. Installation requires no wiring or soldering. VIFLY Beacon.

Locator buzzer designed to help find FPV drones and RC aircraft after power or control signal loss. The built-in 80 mAh LiPo battery allows operation after the main battery is disconnected, while the sound level reaches up to 110 dB. VIFLY Finder 2.

Six-channel VIFLY WhoopStor 3 charger and discharger for 1S LiPo and LiHV batteries with PH2.0 and BT2.0 connectors. Supports adjustable charging current from 0.3A to 1.3A per channel and Storage mode at 3.80V/3.85V. Black enclosure version. VIFLY WhoopStor 3