Gravity: Digital Weight Sensor - set with a pressure sensor (measuring module + strain gauge beam)
ID: 581646
5906623406593
zł82.45
Tax included
zł67.03 tax excl.
Set with the ADC HX711 transducer module and a pressure sensor in the form of a tensometric beam. It communicates via the UART interface. It allows you to build a simple home scale. DFRobot SEN0160
Description
Set with the ADC HX711 transducer module and a pressure sensor in the form of a tensometric beam. HX711 to0 24-bit analog-to-digital converter with differential input channels. It has a built-in voltage stabilizer to power the system and the pressure sensor. It communicates via the UART serial interface. A strain gauge beam with a measuring range up to 1 kg has been attached to the module. The kit allows you to build a simple home scale, but it can also be used in industrial measuring applications. The product wiki page offers a user manual and sample programs.
Features
Measuring module (HX711)
- Two differential input channels
- Built-in low noise PGA chip with selectable 32, 64 and 128 gain
- Built-in voltage stabilizer
- Built-in oscillator
- UART interface
- 10SPS or 80SPS output data rate selectable
- Supply voltage: 2.6 V to 5.5 V
- Current: <1.6 mA
- Working temperature: -40 to 85 ° C
Strain gauge beam
- Measurement range: 1 kg
- Excitation voltage: 5 to 15V
- Output sensitivity: 1.0 ± 0.15 mV / V
- Error: 1% of full scale
- Zero shift: 0.05 / 0.03 ~ 30min）% FS
- Temperature offset: 0.05 / 0.03% F.S / 10 ° C
- Zero output: ± 0.1 mV / V
- Input impedance: 1055 ± 15 Ω
- Output impedance: 1000 ± 5 Ω
- Overload capability: 200% FS
- Interface: analog output
- Dimensions: 33 x 38 mm
Kit contains
- Measurement module
- Strain gauge beam
- 2 x Gravity cable
581646
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.42
Delivery date unknown
No product available!
Available
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł21.65
24h
Available quantity: 1
Available
Board with ATmega1280 microcontroller from the AVR family, the user has 54 I/O lines, 14 PWM channels, 16 analog inputs. DFRobot DFR0003
zł89.20
Delivery date unknown
No product available!
Other products in the same category (16)
Flexible pressure sensor with dimensions of 400x15 mm. Designed to detect static and dynamic pressure at high reaction speed. DFRobot SEN0299
zł48.04
24h
Available quantity: 2
Available
SEN-11207 - Flexiforce Pressure Sensor - 25lbs (1" area)
zł213.71
24h
Available quantity: 3
Available
Grove module with FSR402 pressure sensor. The board is equipped with a Grove connector with an analog output. Seeed Studio 101020553
zł75.90
4 weeks
No product available!
The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. BOB-13878
zł13.26
24h
Available quantity: 5
Available
Educational module for measuring force in the range from 30 g to 1.5 kg, based on a flexible material that responds with a change in the analog signal. Thanks to its small thickness (0.4 mm), fast response and compatibility with Arduino, micro:bit and Unihiker, it is ideal for teaching physics, engineering and DIY projects. DFRobot SEN0616
zł22.74
24h
Available quantity: 1
Available
This disc load cell (sometimes called a strain gauge) can translate up to a whopping 200kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the disc. SEN-13332
zł473.76
24h
Available quantity: 1
Available
Simple-to-use, open source solution for measuring weight and temperature with the ability to read multiple types of load cells and offers a simple-to-use serial menu to configure calibration value, sample rate, time stamp and units of precision. SEN-13261
zł178.41
24h
Available quantity: 2
Available
A round, flexible, pressure sensor that can be used to realize very sensitive force detection. The sensor is durable and designed to detect static and dynamic pressure at high reaction speed. DFRobot SEN0298
zł17.45
24h
Available quantity: 1
Available
Flexiforce Pressure Sensor A201 – 1lb, Tekscan, RoHS
zł99.51
24h
Available quantity: 1
Available
M5Stack U177 – Unit Mini Scales is a ready-to-use weighing module based on the HX711 and STM32, featuring I2C communication and support for popular platforms. It is used in laboratory, production and educational projects that require precise mass measurement.
zł37.39
24h
Available quantity: 1
Available
Flexible pressure sensor with dimensions of 40 x 40 mm. Designed to detect static and dynamic pressure at high reaction speed. DFRobot SEN0296
zł37.24
24h
Available quantity: 6
Available
Aluminum tensometer beam, allowing weight measurement up to 2 kilograms. It has four wires. It is used in kitchen scales and portable scales.
zł14.34
24h
Available quantity: 34
Available
Round, flexible, pressure sensor that can be used to implement very sensitive force detection. The sensor is durable and designed to detect static and dynamic pressure at high response speeds. DFRobot SEN0295
zł49.72
4 weeks
No product available!
Available
Deflection sensor 114 mm long. The sensor resistance changes with the bend angle. At the end, the sensor has a 2-pin connector with a pitch of 2.54 mm. SparkFun SEN-08606
zł112.40
24h
Available quantity: 3
Available
Available
Set with the ADC HX711 transducer module and a pressure sensor in the form of a tensometric beam. It communicates via the UART interface. It allows you to build a simple home scale. DFRobot SEN0160