- Out-of-Stock
AVT728 A
ID: 192763
FULL SCREENED SENSOR - PRINTED PLATE
FULL SCREENED SENSOR - PRINTED PLATE
Producer: AVT
A great toy using a light-emitting diode. With one or two touch sensors, the system allows you to control the color of a two-color LED. Despite its simplicity, it is a modern replacement for classic mechanical switches. One of the applications is the electronic simulation of a coin toss, or the popular 'eagle or tails' game. An excellent layout for experiments that allow you to get to know the operation of touch sensors.
The device is recommended for all experimenters and lovers of light effects
Selected parameters:
- two-color LED diode with a diameter of 10 mm
- two modes of operation (selected by jumpers); with one or two buttons
- determined rest state of the system after switching on the power supply
- the possibility of replacing contact sensor buttons
- power supply - 6-15 V
- printed circuit board and documentation included
A version with a set of independent components is available
- Detailed description in
Download
192763
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Pre-installed Ubuntu 16.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung. JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode. The eMMC chipset is only compatible with Amlogic S905 and S805 series(ODROID-C1+ / C0 / C2)
Retired
No product available!
A module with a color and gesture sensor based on the APDS-9960 chip. It can detect simple hand gestures, RGB colors and measure ambient light. DFRobot SEN0187
Retired
No product available!
Power Supply 2.5A 5.1V for Raspberry Pi 3 model B - STONTRONICS T5875DV
Retired
No product available!
Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
Retired
No product available!
No product available!
No product available!
Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
Retired
No product available!
Pre-installed Android 4.x or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
Retired
No product available!
3.2D soldering tip, flat screwdriver 5.5mm in diameter, for WEP 926 soldering station
Retired
No product available!
Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
Retired
No product available!
5V / 3.1A eXtreme power supply with microUSB plug for all Raspberry Pi computers (including Pi 3 model B and Pi 3 model B +)
Retired
No product available!
Antenna with built-in LNA amplifier with high sensitivity, for mounting in a device using a GPS module. The antenna has a 25mm cable, terminated with a U.FL plug (IPEX). Dimensions of the device: 9 x 9 x 4mm
Retired
No product available!
The GY-GPS6MV1 module is a board containing the U-blox NEO-6M GPS receiver system. The tile also includes RTC backup battery, antenna connector (U.FL), voltage stabilizer and UART signal outputs
Retired
No product available!
Kit: MAXimator, MAXimator Expander, ZL32PRG - USB Blaster PRO
Retired
No product available!
Power Supply 2.5A 5.1V for Raspberry Pi 3 model B - STONTRONICS T5875DV
Retired
No product available!
MYD-JA5D44 Development Board is a complete educational platform. Its heart is the MYIR MYC-JA5D44 module, which was equipped with the Atmel SAMA5D44 processor based on Cortex-A5 cores. The processor can work at a maximum frequency of 600 MHz. Min. RS232, RS485 connectors, HDMI connector, 3.5 mm Jack Audio inputs, microSD memory card slot, 10/100 Mbps Ethernet slot and many more.
Retired
No product available!
FULL SCREENED SENSOR - PRINTED PLATE