- Out-of-Stock

RoboClaw 2x60AHV Motor Controller (V7C) is a two-channel DC motor driver, operating voltage: 10,5 to 60V, maximum continuous current: 60A, the ability to easily implement feedback loops with PID controller, security systems. Pololu 3583
RoboClaw 2x60AHV Motor Controller (V7C) is a two-channel DC motor driver that can independently control the operation of two motors. The control can be done via USB port, serial TTL interface, signal from RC receiver or through analog input. The controller has built-in decoder quadrature encoders, which allow easy implementation of the closed loop of engine speed control. The option of energy recovery during engine braking, resistance to sudden changes in speed (at high engine revolutions), and the control system of battery charge and cut-off in case of too deep discharge should be considered as an additional, noteworthy option. These are very convenient and useful properties that will certainly simplify the construction of not one mobile construction.
The presented version of the controller has two channels, each of which has a capacity of 60 A at constant power consumption, while the maximum current value of the current consumed is 120 A. The voltage supplying the motors is from 10,5 to 60 V. The module also has a modified cooling circuit, which is more efficient than the RoboClaw 2x60A version.
Unlike the older version of the controller (V5 and lower), this version has a plastic base that protects the plate from the bottom. This version also has a connector for connecting an optional fan for cooling the controller's heat sink. The controller has the same dimensions as its predecessors, and the arrangement of such elements as buttons, goldpin pins, mounting holes, connectors has not changed.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Blue USB 3.0 A cable - microUSB 3.0 B with 1m length, allowing SuperSpeed transmission (up to 5Gbit / s = 625MB / s)
The RoboClaw Solo motor controllers from Basicmicro (formerly Ion Motion Control) can control a single brushed DC motor using USB serial, TTL serial, RC, or analog inputs. An integrated quadrature decoder make it easy to create a closed-loop speed control system.
No product available!
The RoboClaw Solo motor controllers from Basicmicro (formerly Ion Motion Control) can control a single brushed DC motor using USB serial, TTL serial, RC, or analog inputs. Pololu 3291
No product available!
Cable with USB typ A and microUSB typ B connectors, cable length 1 m. LANBERG CCP-MUSB2-AMBM-W-1M
Convenient to use retractable 3in1 USB cable with USB A plug and three output connectors: microUSB, USB Type C and Lightning
No product available!
HK NTM Prop Drive Series 28-30 900kv / 300W Brushless Motor (52858)
No product available!
COM-11556 - Thermochromatic Pigment - Sapphire Blue (20g)
No product available!
No product available!
No product available!
No product available!
The ISM radio module in the SMD housing. It works on 433MHz frequency. The module complies with FCC, ETSI regulations. HOPE MICROELECTRONICS RFM12B-433S2P
No product available!
No product available!
No product available!
Permanent cylindrical neodymium magnet with a diameter of 3 mm and a height of 1,5 mm.
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
Printed circuit board for the Lattice PLP programmer
No product available!
No product available!
RoboClaw 2x60AHV Motor Controller (V7C) is a two-channel DC motor driver, operating voltage: 10,5 to 60V, maximum continuous current: 60A, the ability to easily implement feedback loops with PID controller, security systems. Pololu 3583