zł43.34 tax excl.
This precision barometric pressure and temperature sensor is ideal for environmental applications. Its low noise floor allows for detection of elevation changes down to approximately 1 cm and offers a relative accuracy of ±0.4 Pa. It supports I2C and SPI interfaces for easy integration with microcontrollers. The pre-assembled module includes a built-in 3.3V regulator, logic level conversion, and STEMMA QT connectors. Adafruit 6407
Adafruit BMP581 is an advanced barometric pressure and temperature sensor, representing the latest generation of Bosch BMP58x series sensors. This high-precision module is ideal as a precise altimeter or for environmental monitoring systems. Its low noise level allows detection of altitude changes from approximately 1 cm (0.08 Pa). The BMP581 supports both I2C and SPI interfaces, enabling easy integration with various microcontrollers and electronic projects.
The sensor offers remarkable relative pressure accuracy of ±0.4 Pa within the 900–1100 hPa pressure range at 25°C, corresponding to roughly ±3.3 cm in altitude. Typical absolute accuracy is ±30 Pa (~2.5 m). It can also measure temperature with an accuracy of ±0.5°C. The BMP581 is fully software-compatible with the BMP580 but provides higher precision and reliability, making it ideal where accurate data is critical. The module is mounted on a ready-to-use PCB with a 3.3 V voltage regulator and logic level conversion, allowing use with both 3 V and 5 V microcontrollers. STEMMA QT connectors enable quick connections and daisy-chaining with other Qwiic-compatible modules. The BMP581 is well-suited for drones, flight stabilization systems, wearables, IoT projects, and anywhere precise altitude and temperature measurement is needed with easy integration.
Data sheet
Manufacturer
Responsible person
4-wire cable with a length of 50 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4399
4-wire cable with a length of 100 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4210
4-core cable with a length of 200 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4401
No product available!
4-core cable with a length of 300 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 5384
4-core cable with a length of 400 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 5385
Module with a GPS receiver based on the MTK3333 chip. It is equipped with a STEMMA QT connector and communicates via the UART or I2C interface. Adafruit 4415
A module with a fan controller and a temperature sensor based on the EMC2101 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4808
Module with digital barometer BMP388. It measures pressure in the range from 300 to 1250 hPa and communicates via I2C or SPI. Adafruit 3966
Air quality sensor module PMSA003I. It allows for a precise analysis of the amount of pollutants in the environment based on the concentration of PM1.0, PM2.5 and PM10 particles. Adafruit 4632
Module with acceleration and rotational speed sensor based on the MPU-6050 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 3886
No product available!
The expansion module is designed to work with the Raspberry Pi 400. The board has a 40-pin connector placed in a vertical position and a connector for RPI 400 at an angle of 45°. Adafruit 4862
Module with a temperature and humidity sensor based on the HTU31 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4832
The module with a black and white OLED display with a diagonal of 0.91" and a resolution of 128x32 pixels. Equipped with a STEMMA QT connector, communicates via the I2C interface. Adafruit 4440
Module with sensor TMP117. It enables measurement in the range from –55°C to 150°C with a very high accuracy up to ± 0.1°C. It communicates via the I2C interface. Adafruit 4821
A module with an acceleration and rotational speed sensor based on the LSM6DSOX system and the LIS3MDL magnetometer. Equipped with a STEMMA QT connector, it communicates via the I2C, SPI or I3C interface. Adafruit 4517
No product available!
Air quality sensor module based on the SGP40 system. It uses CMOSens technology by Sensirion and provides information on the concentration of volatile organic compounds (VOC). Adafruit 4829
Adapter dedicated to the Nintendo Wii Nunchuck. It allows you to connect the controller to the development board via the I2C interface. Adafruit 4836
Module with a logarithmic digital potentiometer based on the DS1841 chip. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4570
Module with acceleration and rotational speed sensor based on the LSM6DSO32 chip. Equipped with a STEMMA QT connector, it communicates via the I2C or SPI interface. Adafruit 4692
Module with a digital barometer LPS22. It enables pressure measurement in the range from 260 to 1260 hPa and communicates via I2C or SPI. Adafruit 4633
Module with an ISO1540 bidirectional galvanic isolator. It allows to electrically separate two devices communicating via the I2C interface. Adafruit 4903
This precision barometric pressure and temperature sensor is ideal for environmental applications. Its low noise floor allows for detection of elevation changes down to approximately 1 cm and offers a relative accuracy of ±0.4 Pa. It supports I2C and SPI interfaces for easy integration with microcontrollers. The pre-assembled module includes a built-in 3.3V regulator, logic level conversion, and STEMMA QT connectors. Adafruit 6407