

zł20.39 tax excl.
The module with the buffer of the I2C bus based on the TCA4307 system. It allows you to connect I2C devices with active power supply. Equipped with a STEMMA QT connector. Adafruit 5159
I2C bus buffer module based on the TCA4307 chip. It allows you to freely connect I2C devices with active power supply, without fear that the bus will hang due to an additional SCL pulse or an unexpected capacitive load. Perfect for prototyping devices, where we often disconnect and connect peripheral modules, because the TCA4307 chip protects against unwanted interference. The module has two STEMMA QT connectors: IN, to which the controller is connected, and OUT, to connect the I2C device. There is also an additional ENABLE pin on the board, which is used to disable the bus, and the READY pin, which will inform you whether the peripheral device is connected and ready to work. The module is compatible with 3.3 V and 5 V systems. Full documentation is available on the product page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Flexible Qwiic cable 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single male goldpin connectors. SparkFun PRT-17912
No product available!
Flexible Qwiic cable, 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single female goldpin connectors. SparkFun PRT-17261
No product available!
Flexible 4-core cable, 50 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17260
No product available!
Flexible 4-core cable, 100 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17259
Flexible 4-core cable, 200 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17258
No product available!
Flexible 4-core cable, 500 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17257
No product available!
Module with 9-axis IMU sensor BNO055. It has a built-in processing chip that returns orientation in 3D space. Communicates via I2C. Adafruit 4646
Module with 3-axis accelerometer and ISM330DHCX gyroscope. Equipped with a STEMMA QT connector, it communicates via the I2C or SPI interface. Adafruit 4502
Module with MLX90640 thermal imaging camera with a matrix of 32x24 fields and a viewing angle of 110°. The board is equipped with a STEMMA QT connector and communicates via the I2C interface. Adafruit 4469
Module with a 16-channel GPIO expander with the ability to control LEDs. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4886
Module with a voltage level converter from 5 V to 3.3 V, intended for use in the STEMMA QT/Qwiic system. It has a built-in voltage stabilizer providing 3.3 V power supply with a current of up to 500 mA. Adafruit 5637
Module with a temperature and humidity sensor based on the SHT40 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4885
Module with waterproof barometer LPS33HW. It enables pressure measurement in the range from 260 to 1260 hPa and communicates via I2C or SPI. Adafruit 4414
Clock signal generator with a frequency of 8 kHz to 160 MHz based on the SI5351A integrated circuit. Communication with the module takes place via the I2C bus. Adafruit 5640
Module with a 3-axis magnetometer based on the MLX90393 system. It has a measuring range from ± 5mT to ± 50mT and a resolution of 0.161 µT. The I2C or SPI interface is used for communication. Adafruit 4022
Module with 8-bit ADC and 8-bit DAC. It allows you to measure voltage and generate an analog signal. Communicates via I2C. Adafruit 4648
Module with ENS160 gas sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C or SPI interface. Adafruit 5606
Module with a 3-axis magnetic field sensor MMC5603. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5579
Module with 12-channel MPR121 capacitive touch sensor. The board is equipped with a Stemma QT connector and communicates via the I2C interface. Adafruit 4830
High-quality OV5640 camera with a 5 MP sensor, 120° wide-angle lens, and support circuitry, ready to work with Pico or Pico W. Adafruit 5949
The module allows you to connect 4 arcade buttons with LED backlight. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5296
Module with acceleration and rotational speed sensor based on the MPU-6050 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 3886
The module with the buffer of the I2C bus based on the TCA4307 system. It allows you to connect I2C devices with active power supply. Equipped with a STEMMA QT connector. Adafruit 5159