Category: RETIRED PRODUCTS

Module with 6 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM187

A module with 5 buttons and an RGB diode, designed to work with the Raspberry Pi. The buttons are connected to the minicomputer through the GPIO expander controlled by the I2C interface. Pimoroni PIM301

Kit for controlling soil moisture of cultivated plants. It contains the HAT Mini module, soil moisture sensors and pots and seeds of herbs: basil, coriander and rosemary. Pimoroni PIM518

Kit for controlling soil moisture of cultivated plants. It contains the HAT Mini module, soil moisture sensors and pots and seeds of chilli. Pimoroni PIM519

A module with a spectrum sensor that operates in the visible light range (450-650 nm). It allows you to measure and characterize a light source or check how the tested surface absorbs or reflects light at specific wavelengths. Pimoroni PIM412

Module with 6-axis IMU motion sensor that combines a 3-axis accelerometer and a 3-axis magnetometer in one system. It communicates via the I2C bus. Pimoroni PIM376

A pin expander designed for Raspberry Pi boards. It is equipped with a standard 40-pin connector for connecting a minicomputer and five sets of 2x20-pin outputs for connecting expansion modules. Pimoroni PIM322

Module with two 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM527

Module with two 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM526

The system of a practical clock with an extremely simple design is equipped with a readable LED display, an alarm clock with a snooze function, and battery backup of the clock operation after a power failure

Kit with DA7280 vibration motor driver module and LRA (Linear Resonant Actuator) motor. It allows you to add vibration feedback from the device to the project. SparkFun ROB-18247

Kit with Jetson Mate base board designed for SoM modules NVIDIA Jetson Nano and Jetson Xavier NX. It allows you to connect 4 SoM modules and create a home GPU computing cluster or server. Seeed Studio 110991411

Jetson Mate motherboard for NVIDIA Jetson Nano and Jetson Xavier NX. It allows you to connect 4 SoM modules and create a home GPU computing cluster or server. Seeed Studio 114992562

ToF distance sensor (Time of flight) with a range of up to 2.5 m. The module is powered with the voltage of 3.3 V and communicates via the I2C interface. SparkFun SPX-17716

A pin expander designed for Raspberry Pi boards. It is equipped with a standard 40-pin connector for connecting a minicomputer and two sets of 2x20-pin outputs for connecting expansion modules. Pimoroni PIM511

A pin expander designed for Raspberry Pi boards. It is equipped with a standard 40-pin connector for connecting a minicomputer and five sets of 2x20-pin outputs for connecting expansion modules. Pimoroni PIM321

Li-Po battery with a rated voltage of 3.7 V and a capacity of 1350 mAh, equipped with a PCM protection and a 1.5 JST-ZH connector. Akyga LP503758

A module with a MEMS microphone and an amplifier that will allow you to detect a voice, a clap or a door slam. The board has an analog output. SparkFun BOB-18011

Module with a 3-axis MMA8452Q accelerometer. The system has a configurable measurement scale of ±2g/±4g/±8g. It is supplied with the voltage from 1.95 to 3.3 V and communicates via the I2C interface. SparkFun SEN-12756

External enclosure designed to protect, transfer and store data on 2.5” HDD and SSD drives with SATA interface. UGO UKZ-1531