Category: STARTER KITS, PROGRAMMERS, MODULES

Module with an integrated proximity and ambient light sensor based on the VCNL4040 system. It can detect obstacles in the range of 0 to 20 cm. It communicates via the I2C bus. Adafruit 4161

Gravity: Digital Crash sensor is a microswitch module (left) often called a limit switch. The module is powered by 5V voltage and has a digital two-state output. DFRobot SEN0138-L

GrovePi + is an extension in the form of a HAT overlay intended for Raspberry Pi computers (B / B + / A + / 2/3/3 +). The module has 15 connectors to which modules / sensors compatible with the Grove standard can be connected. Seeed Studio 103010002

Gravity: UART MP3 Voice Module is an MP3 sound player module with a built-in 8 MB memory. It is powered by 3.3-5V and controlled by the UART interface. DFRobot DFR0534

Module with a temperature and humidity sensor based on the HTU31 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4832

Module with BME680 sensor for measuring environmental conditions such as concentration of volatile organic compounds (VOC), atmospheric pressure, temperature and humidity. I2C or SPI communication. SparkFun SEN-16466

Module with three Hall sensors A3144E, which react to the failure of the magnet. It is powered with 5 V and has a digital output on the Grove connector. M5Stack U084

Module with WiFi Espressif ESP32-S2 WROOM. It integrates a set of peripheral devices - capacitive touch sensors, SPI, UART, I2S and I2C. SparkFun WRL-15663

Adapter with 18-pin FPC connector with 0.5 mm pitch designed for QT Py and Xiao boards. It has pin-outs on the edge connectors. Dedicated to Adafruit\'s EYESPI series displays. Adafruit 5772

A 30 cm long connecting cable (4 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF04S connector that KAmod modules are equipped with. cabhu04-30

Gravity: Analog Sound Sensor is a sound sensor with Gravity analogue output. The module can be supplied with 3.3 ... 5V voltage. DFRobot DFR0034

12-bit DAC converter module designed to work with the M5Stack sets. It enables the conversion of digital signals into an analog signal. M5Stack DAC Unit

Gravity: I2C 12-Bit DAC is a module with 12-bit DAC and built-in EEPROM memory. The module is powered by 3.3 ... 5V for communication used by the I2C interface. DFRobot DFR0552

Module with a button and re LED backlight. Controlled by the I2C interface, it has a built-in debouncing mechanism, pull-up resistors as well as interrupts and a FIFO queue. SparkFun BOB-15932

Module with WiFi Espressif ESP32-S2. It integrates two regulators, SPI Flash memory, LiPo charging circuit and RGB diode. It is equipped with a STEMMA QT connector. Adafruit 4775

Module with a 4-inch touch display that uses two MCU systems (ESP32-S3 and RP2040) and supports Wi-Fi, BLE and LoRa communication. The board is equipped with USB Type C, I2C (Grove) and analog inputs interfaces and can easily connect to other peripheral devices. Seeed Studio 114993070

Gravity sensor adapter with 3-pin terminal connector. There are two 10 kΩ pull-up and pull down resistors on the board, set with a jumper. DFRobot DFR0055

A comprehensive development base, ideal for IoT projects. It offers a DC-DC circuit converting voltage from 9 from 24 V to 5 V, Grove expansion ports and an area with prototype holes with a 2.54 mm pitch. M5Stack K026-B

Battery with a capacity of 190 mAh designed to power the M5ATOM series modules. M5Stack T001

Espressif ESP32-S3 WiFi and Bluetooth LE module board. It offers 16 MB of flash memory and 2 MB of SRAM. The pinouts are compatible with the HAT modules for the Raspberry Pi Pico. Waveshare ESP32-S3-Pico-M