Category: STARTER KITS, PROGRAMMERS, MODULES

An expansion board with digital outputs (for industrial applications) designed to work with the STM32 Nucleo kits. The module is based on a single high-side switch IPS160HF. STMicroelectronics X-NUCLEO-OUT08A1

Module with the 3-axis ADXL313 accelerometer with measuring ranges of ± 0.5 g, ± 1 g, ± 2 g or ± 4 g. The system is characterized by high 13-bit resolution and low power consumption. SparkFun SEN-17241

Miniature pressure measurement module equipped with a 25 psi piezoresistive pressure sensor. It allows you to perform calibrated and compensated pressure measurements from 60 mbar to 2.5 bar. SparkFun SEN-16476

ATOM Lite development kit complete with programmable AC/DC HUB switch module. M5Stack ATOM SWITCH

Starter kit with Qwiic modules designed to work with the Raspberry Pi. The set consists of an overlay for Raspberry Pi with a standard 40-pin connector and four Qwiic connectors, OLED display, VCNL4040 distance sensor and environmental sensors. SparkFun KIT-16841

ATOM Lite development kit complete with DRV8825 stepper motor driver module. M5Stack ATOM STEPMOTOR

Data logger pre-programmed to automatically record data from IMU, GPS and Qwiic series sensors. SparkFun DEV-16832

Extension board with distance sensor ToF VL53L1, The sensor has a range of up to 400 cm. The kit includes 2 modules with sensors that can be connected via a 10-pin connector. The shield is compatible with STM32 Nucleo boards and has an Arduino UNO R3 connector. STMicroelectronics X-NUCLEO-53L1A2

An expansion board with digital outputs (for industrial applications) designed to work with the STM32 Nucleo kits. The module is based on the IPS161HF double high-side switch. STMicroelectronics X-NUCLEO-OUT10A1

A device that provides electrical isolation between the J-Trace emulator and the ARM board, which protects against electrical interference, especially in systems where the development tools and the application do not share the same ground. It provides 1 kV DC isolation, supports trace frequencies up to 75 MHz, and is compatible with J-Trace V2 and later versions, with a minimum power consumption of 25 µA. Segger J-Trace Isolator (07/08/10)

MicroMod main module with SAMD51 microcontroller. Equipped with an M.2 connector, it can work with MicroMod expansion boards. SprakFun DEV-16791

MicroMod main module with ESP32 chip. Equipped with an M.2 connector, it can work with MicroMod expansion boards. SprakFun WRL-16781

MicroMod main module equipped with Bluetooth 5.0 Sparkfun Artemis. Equipped with an M.2 connector, it can work with MicroMod expansion boards. SprakFun DEV-16401

GPS module with NEO-M9N 92-channel GNSS receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. SparkFun GPS-15712

Extension board designed for MicroMod main modules. Equipped with digital microphones, accelerometer and camera connector. A great tool for machine learning projects. SparkFun DEV-16400

Module with WiFi and Bluetooth Espressif ESP32 WROOM. It integrates a set of peripheral devices - capacitive touch sensors, Hall sensors, SD card interface, Ethernet, fast SPI, UART, I2S and I2C. SparkFun WRL-15663

J-Link ARM-14 Adapter, RoHS

Ammeter module designed for M5Stack sets. It can measure direct current in the range from 0 to 4 A with a resolution of approx. 0.15 mA. M5Stack U086

Module with 4 relays JZC-11F with a load of 5A. It enables switching devices with high power using a microcontroller. I2C communication. SparkFun COM-16566

Module with a button and green LED backlight. Controlled by the I2C interface, it has a built-in debouncing mechanism, pull-up resistors as well as interrupts and a FIFO queue. SparkFun BOB-16842