Category: STARTER KITS, PROGRAMMERS, MODULES

Extension board designed for MicroMod processor modules. All the pins are led out to connectors with a pitch of 2.54 mm. SparkFun DEV-16885

A set for building a walking robot. The chassis is equipped with four servos, a controller and an STM32F030 microcontroller. M5Stack U086

Development kit with ATSAMD21E microcontroller with ARM Cortex M0+ core. The chip can be clocked at 48 MHz, has a built-in 256 KB of Flash memory and 32 KB of SRAM. The module has a Qwiic connector. SparkFun DEV-15423

Development kit with ATSAMD51J20 microcontroller with ARM Cortex M4F core. It is clocked at 120 MHz, has 1 MB of Flash and 256 KB of SRAM. There are 6 SERCOM interfaces on the board. SparkFun DEV-14713

Module with a capacitive touch sensor based on the CAP1203 chip. There are three touch panels on the board that can be used as separate sensors (pins CS1, CS2, CS3) or as a touch slider. I2C communication. SparkFun SEN-15344

Development kit with XBee3 Micro radio module. Provides plug and play 802.15.4 2.4 GHz wireless connection (Zigbee 3.0 protocol). SparkFun WRL-15435

Development kit with XBee3 Micro radio module. Provides plug and play 802.15.4 2.4 GHz wireless connection (Zigbee 3.0 protocol). SparkFun WRL-15454

Shield with Qwiic connectors designed for Raspberry Pi minicomputers. It allows you to easily connect the minicomputer with the Qwiic sensor system. SparkFun DEV-15945

Module with 16-channel PCA9685 servo driver designed for Raspberry Pi minicomputers. The board is equipped with a USB Type C power connector. SparkFun DEV-15316

The expansion module is designed for micro:bit sets. Offers a simple, beginner-friendly robotics controller. SparkFun DEV-15713

Ammeter module designed for M5Stack sets. It can measure direct current in the range from 0 to 4 A with a resolution of approx. 0.15 mA. M5Stack U086

Voltmeter module for M5Stack sets. It can measure DC voltage in the range from 0 to 36 V with an accuracy of approx. 0.5 mV. M5Stack U087

Module with a PIR motion sensor designed for M5Stack modules. It can detect movement up to 5 meters with a detection angle of 100 degrees. M5Stack U004

J-Link PRO programmer with PoE support as an alternative to USB connection. Allows you to reduce the size of cable bundles in test farms. It offers data transfer speeds of up to 4 MB/s and no limits on the number of breakpoints. It supports various operating systems, including Microsoft Windows (x86/x64), Linux (x86/x64/Arm) and macOS (x86/Apple M1). J-Link PRO PoE (8/12/28)

GPS module with 72-channel GNSS SAM-M8Q receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART and I2C interfaces. SparkFun GPS-15210

Module with laser distance sensor ToF VL53L0X designed for M5Stack sets. It can detect simple hand gestures. M5Stack U010

Module with the 3-axis ADXL313 accelerometer with measuring ranges of ± 0.5 g, ± 1 g, ± 2 g or ± 4 g. The system is characterized by high 13-bit resolution and low power consumption. SparkFun SEN-17241

Data logger pre-programmed to automatically record data from IMU, GPS and Qwiic series sensors. SparkFun DEV-16832

Extension board with distance sensor ToF VL53L1, The sensor has a range of up to 400 cm. The kit includes 2 modules with sensors that can be connected via a 10-pin connector. The shield is compatible with STM32 Nucleo boards and has an Arduino UNO R3 connector. STMicroelectronics X-NUCLEO-53L1A2

An expansion board with digital outputs (for industrial applications) designed to work with the STM32 Nucleo kits. The module is based on a single high-side switch IPS160HF. STMicroelectronics X-NUCLEO-OUT08A1