Category: STARTER KITS, PROGRAMMERS, MODULES

Module for learning the basics of electronic engineering; illustrates the relationship between voltage, current, and allows the generation and observation of signals. It has the ability to sample the signal up to 200kSPS in a 16-bit converter. Powered from the USB port. ADALM1000

Module with pressure, humidity and temperature sensor. It uses the I2C interface and allows the connection of additional wind sensors via the RJ11 connector. SparkFun DEV-13674

X-NUCLEO-IDS01A5 is a development board STM32 Nucleo that allows you to use the RF SPSGRF-915 module on the ISM band (915 MHz carrier).

Conductivity Sensor Switch DFRobot is a touch button that allows you to change the sensor output status by connecting terminals (positive and negative) using metal, human body or fruit and plants. It is powered by 3.3 ... 5 V. DFRobot SEN0223

The Segger J-Link Mictor 38 Adapter allows connection to a 38-pin Mictor connector in accordance with the ARM "ETM" specification. The adapter connects the GND and JTAG pins to the 20-pin J-Link, and the trace pins on the Mictor connector are not used.

Development kit containing the M24SR64 EEPROM chip. It can be operated by an I2C interface, a 13.56 MHz RFID reader or a phone with NFC. Version with Bluetooth module and headset

Gravity: Analog TDS Sensor / Meter is an analog water purity measurement module. It is powered by 3.3 ... 5.5V voltage and has an analogue output interface. Module compatible with Arduino. DFRobot SEN0244

PmodCMPS2 is a module with a digital magnetometer based on the Memsic MMC34160PJ system. It has a resolution of 0.5 mG (within ± 16) and accuracy up to 1 °. For communication with the module, an I2C interface is provided on the 6-pin Pmod connector. Digilent 410-355

SEN-14351

SEN-14347

GPS-14414

Arducam Nano RPI Module is a minicomputer equipped with Broadcom BCM2835 processor and VideoCore IV GPU. The module has two CSI connectors for connecting cameras, video output (PAL), SPI, I2C, UART, and GPIO. ArduCam B0101

The STM32L4R9I-EVAL evaluation set was designed to demonstrate the capabilities of the STM32L4R9AI microcontroller. Mounted connectors allow easy connection of extensions. The board also has a debugger / ST-LINK / V2-1 programmer. STM32L4R9I-EVAL

Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, Li-Pol battery charging system. The board has soldered goldpin connectors. Adafruit 3591

Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, the module has a built-in system for charging Li-Pol batteries. The plate has soldered goldpin connectors (female extension). Adafruit 3619

Small development kit with ATmega32u4 microcontroller. The board has 6 power, 6 analog and 17 digital pins, which makes it have similar capabilities to the Arduino UNO. Compatible with Arduino. Adafruit 3675

Waveshare Core429I is a PCB with STM32F429IGT6 microcontroller, contains necessary elements for microcontroller operation, all GPIOs connected to goldpin connectors

Pcam 5C: 5 MP Fixed Focus Color Camera Module with Omnivision OV5640 5 megapixel (MP) color image sensor which includes various internal processing functions, incl. automatic white balance, automatic black level calibration, and controls for adjusting saturation, hue, gamma and sharpness. Digilent 410-358

The Digilent Pmod COLOR is a color sensor module with the ability to sense red, green, blue and clear light. Digilent 410-348

The Pmod CAN is a CAN 2.0B controller with an integrated transceiver. The embedded Microchip MCP25625 chip connects directly to the physical CAN bus and meets automotive requirements for high-speed (1 Mb/s), low quiescent current, electromagnetic compatibility, and electrostatic discharge. Digilent 410-353