Category: STARTER KITS, PROGRAMMERS, MODULES

Pmod MTDS is a module with a 2.8-inch LCD display. It has a resolution of 320x240 pixels. It has touch support (capacitive, 2 point). Digilent 410-341

A cryptography kit that allows you to learn the basics of cryptographic authentication and the ATECC508A cryptographic co-processor. SparkFun KIT-18303

8 MB PSRAM memory chip, designed for mounting on Teensy 4.1 boards. It enables the expansion of the memory of the microcontroller. PJRC IC-PSRAM-8MB-SOIC8

LIDAR distance sensor with a measuring range from 5 cm to 10 m and a resolution of 1 cm. It communicates via the I2C or ANT interface. The set includes a module with Qwiic SparkFun SEN-18009 connectors

The Pmod CAN is a CAN 2.0B controller with an integrated transceiver. The embedded Microchip MCP25625 chip connects directly to the physical CAN bus and meets automotive requirements for high-speed (1 Mb/s), low quiescent current, electromagnetic compatibility, and electrostatic discharge. Digilent 410-353

ML accelerator module that allows the use of the Edge TPU coprocessor in existing systems. It will be used in projects using machine learning and artificial intelligence. Coral M.2 Accelerator with Dual Edge TPU G650-06076-01

The Digilent Pmod COLOR is a color sensor module with the ability to sense red, green, blue and clear light. Digilent 410-348

Development board with LoRa Semtech SX1262 module and Apollo 3 Bluetooth 5 integrated in the NM180100 chip. It supports the 868 MHz and 915 MHz bands and Bluetooth Low Energy. It is compatible with the Qwicc system. SparkFun 17506

TPL5110 external counter module to turn on a project after a set time and save energy. The TPL5110\'s delay is configurable with resistors ranging from 100 ms to two hours. SparkFun PRT-15353

Small development kit with ATmega32u4 microcontroller. The board has 6 power, 6 analog and 17 digital pins, which makes it have similar capabilities to the Arduino UNO. Compatible with Arduino. Adafruit 3675

Development board designed for IoT projects. It is equipped with a WiFi/Bluetooth module ESP32, LoRa 868 MHz, GPS and a basket for a Li-Ion 18650 battery. TTGO T-Beam V1.1

NUCLEO series starter kit equipped with the STM32G491RE microcontroller (512 kB Flash, Cortex-M4), with a built-in programmer-debugger ST-Link-V3E, equipped with connectors compatible with Arduino. STMicroelectronics NUCLEO-G491RE

Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, Li-Pol battery charging system. The board has soldered goldpin connectors. Adafruit 3591

The STM32L4R9I-EVAL evaluation set was designed to demonstrate the capabilities of the STM32L4R9AI microcontroller. Mounted connectors allow easy connection of extensions. The board also has a debugger / ST-LINK / V2-1 programmer. STM32L4R9I-EVAL

Development board equipped with STM32 series microcontroller (STM32H743IIT6). It is equipped with all the necessary elements for project development, requires an external programmer. Waveshare CoreH743I

An expansion board designed for MicroMod main modules. Equipped with the LTE-M / NB-IoT u-blox SARA-R510M8S module. It allows you to monitor devices remotely. SparkFun DEV-17272

The USB-UART converter is designed to work with the MicroMod Asset Tracker board. It facilitates direct communication with the SARA-R510M8S u-blox module. SparkFun DEV-17725

Single board computer with SOM module NXP i.MX 8M processor, has 4 GB of RAM, 8GB of eMMC memory, wireless communication and TPU coprocessor. It includes numerous connectors, including USB 2.0 / 3.0 ports, DSI interface, CSI-2, Ethernet port, audio connectors and a 40-pin GPIO connector. Google Coral Dev Board 4GB G950-06210-01

SEN-14351

GPIO expansion module designed for FireBeetle boards. It is equipped with a set of connectors to facilitate the connection of sensors. DFRobot DFR0483