Category: STARTER KITS, PROGRAMMERS, MODULES

The set consists of STM32 Nucleo NUCLEO-G431RB plate with STM32G431RB microcontroller, X-NUCLEO-IHM16M1 plate with three-phase STPIN830 BLDC / PMSM motor controller and GBM2804H-100T motor. STMicroelectronics P-NUCLEO-IHM03

Adafruit 2010

Module with a digital rotary encoder controlled by the I2C interface. The potentiometer has RGB LED backlight. The encoder generates post-movement information with 24 levels per revolution and rotation direction detection. SparkFun DEV-15083

Module with a current and voltage sensor dedicated to Feather boards. Can measure voltage up to 26 V and current up to 3.2 A. Based on INA219 sensor, I2C communication. Adafruit 3650

Micro:bit expansion module designed for IoT. The board is equipped with WiFi, a two-channel output for DC motors, 6 IO pins, an I2C, UART interface, a buzzer, RGB diodes and a charging circuit. DFRobot MBT0012

Set (5 pieces) of wires for attaching modeling servos with the Grove system. With one wire you can connect 2 servos to one Grove slot. Seeed studio 110990057

3-port I2C splitter module. The board is equipped with Grove connectors and allows you to connect additional I2C devices. Seeed Studio 103020006

Starter kit from the NUCLEO series equipped with the STM32F070RBT6 microcontroller (128 KB Flash, Cortex-M0), with a built-in programmer-debugger ST-Link/V2, equipped with connectors compatible with Arduino.

Starter kit from the NUCLEO series equipped with STM32G031K8 (64 kB Flash, Cortex-M0+) microcontroller, with embedded ST-Link v.2.1 debugger, connectors compatible with Arduino Nano. STMicroelectronics NUCLEO-G031K8

Module with LoRa transmitter based on RFM95 (SX1276 LoRa®). It works with a frequency of 433 MHz, maximum power up to 100 mW and a power gain of up to + 20dBm. The module has a built-in antenna, but it is possible to connect an external antenna (MHF connector). The module has a connector in accordance with the Grove standard. Seeed studio 113060007

Recorder v3.0 is a module that allows you to record and play sounds. The module was based on the ISD9160FI system, it also has a FLASH memory with a capacity of 2 MB, which allows for recording up to 83 seconds long. The set contains a small loudspeaker on which recorded sounds can be played. Seeed studio 107020029

The Pololu A-Star 32U4 Prime is a general-purpose programmable board based on Atmel’s ATmega32U4 AVR microcontroller and arranged in the common Arduino form factor exemplified by the Uno R3 and Leonardo. Pololu 3107

Expansion board for micro:bit modules with connectors compatible with Boson and Gravity sets. DFRobot DFR0521

A set with a temperature sensor based on the DS18B20 system in the form of a waterproof measuring probe, a sensor adapter and a cable. Communication via the 1-Wire interface. DFRobot KIT0021

JTAG/SWD Emulator with USB interface

ATATMEL-ICE-BASIC is a programmer designed to work with AVR microcontrollers with the On-Chip Debug function and microcontrollers with the ARM Cortex-M core from Atmel. Available interfaces are JTAG, SWD, PDI, TPI, aWire, SPI and debugWire.

Evaluation Board with AD7688, 1xADC, 16-bit, Sampling Rate (Per Second) 500k, Analog Devices, RoHS

Speaker for micro:bit is an expansion module with a loudspeaker designed for micro:bit with volume control and headphone output. Speaker for micro:bit

NXP MRB-KW019032EU is a modular set based on a 32-bit microcontroller with ARM Cortex M0 48 MHz core, equipped with an 868 MHz radio module. MRB-KW019032EU

STM32 Nucleo development board for STM32 F3 series - with STM32F334R8T6 MCU, 64KB flash memory, STM, RoHS