GPS-14414

Pmod SSR is a module with a semiconductor relay. One GPIO port is required for control, the relay is suitable for operation with up to 48 V, it can be used for devices that draw current up to 6 A. Digilent 410-342

Module with acceleration and rotational speed sensor based on the MPU-6050 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 3886

Audio Analyzer is a module with sound analyzer based on the MSGEQ7 system. It divides the sound into seven frequency bands, and then allows you to read the peak levels of each band. It allows you to measure the sound in the following frequencies: 63Hz, 160Hz, 400Hz, 1kHz, 2.5kHz, 6.25kHz and 16kHz. DFRobot DFR0126

Module with a gesture sensor PAJ7620U2, which allows to recognize up to 13 gestures. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020083

Conductivity Sensor Switch DFRobot is a touch button that allows you to change the sensor output status by connecting terminals (positive and negative) using metal, human body or fruit and plants. It is powered by 3.3 ... 5 V. DFRobot SEN0223

Module with a dust sensor PPD42NS. The board is equipped with a Grove cable and communicates via the PWM interface. Seeed Studio 101020012

Gigabit Ethernet transceiver with an FMC interface. Up to 1 Gbps network transfers with the host board using an FMC connector. NET-FMC can be connected any FMC(HPC) interfaces. Terasic P0481

A small module with a temperature sensor (thermistor). As the temperature changes, the resistance of the thermistor changes, which allows the temperature to be measured in the range from -40 to 125 ° C with an accuracy of 1.5 ° C. The module has a connector in accordance with the Grove standard. Seeed studio 101020015

Module with a magnetic sensor based on the CT10 reed switch. CT10 is a unipolar reed switch, normally open. The sensor reacts to the action of an electromagnet, permanent magnet or a combination thereof. The module has a connector in accordance with the Grove standard. Seeedstudio 101020038

Grove module with a small vibration motor. Seeed studio 105020003

Module with a 6-axis IMU sensor (accelerometer and gyroscope) that allows you to measure acceleration and rotational speed in a wide range of ±30g and ±4000dps. Communicates via I2C. Adafruit 4464

Gravity I2C OLED-2864 Display is an OLED display with I2C interface with 128x64 resolution, powered by 3.3-5V. DFRobot DFR0486

Module with FM receiver, with its help it is possible to receive radio waves broadcast in the FM band (frequency 50-115MHz). The module has been equipped with a 3,5mm jack socket, through which you can connect headphones. The module has a connector in accordance with the Grove standard. Seeed Studio 107020006

Module with the OPTIGA TRUST M SLS32AIA cryptographic chip. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4351

Module with acceleration and rotational speed sensor based on the LSM6DSO32 chip. Equipped with a STEMMA QT connector, it communicates via the I2C or SPI interface. Adafruit 4692

Gravity: Digital 10A Relay Module is a module with 10A 35VAC / 30VDC relay compatible with devices with control signals in the range of 2.8 ... 5.5V. DFRobot DFR0473

The Digilent Pmod NAV uses the LSM9DS1 3-axis accelerometer, 3-axis gyroscope, 3-axis magnetometer, plus the LPS25HB digital barometer to provide users with 10-DOF functionality. Digilent 410-326

 relative humidity sensor with integrated temperature sensor for highly accurate measurements at low power. With the TI HDC1080, you can determine the relative humidity of the environment with up to 14 bits of resolution. Digilent 410-347

With an on board Microchip PIC16 MCU, two-axis joystick on a center button, a trigger button, and a programmable RGB LED capable of 24-bit color, the Pmod JSTK2 is ideally suited for Digilent microcontroller or FPGA-based projects that require proportional control from the user, such as robotic applications. Digilent 410-330