DC motor driver with voltage 6.5..40V and maximum continuous current 21A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3149

DC motor driver with voltage 6.5..30V and maximum continuous current 27A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3148

ST72F344K4T6, 8-bit MCU with up to 16 Kbytes Flash memory, 10-bit ADC, two 16-bit timers, two I2C, SPI, SCI, LQFP-32

STP80NF10, MOSFET N-channel, 100 V, 0.012 Ω, 80 A, TO-220

Module with a stepper motor driver based on the DRV8434A system. It allows the bipolar motor to be supplied with current up to 1.2 A per phase and with a voltage from 4.5 V to 45 V. Communication via the SPI interface. Pololu 3767

Module with a stepper motor driver based on the DRV8434A system. It allows the bipolar motor to be powered with a current of up to 1.2 A per phase and can be supplied with the voltage from 4.5 V to 45 V. Pololu 3765

PmodCMPS2 is a module with a digital magnetometer based on the Memsic MMC34160PJ system. It has a resolution of 0.5 mG (within ± 16) and accuracy up to 1 °. For communication with the module, an I2C interface is provided on the 6-pin Pmod connector. Digilent 410-355

E-Ink display module (ePaper) with a diagonal of 2.9 "and a resolution of 296 x 128 pixels with a SPI controller.   Waveshare 12956

E-Ink display (ePaper) with a diagonal of 1.54 "and a resolution of 200 x 200 pixels with a SPI controller. Waveshare 1.54inch e-Paper (B)

WIFI-LPT100 Eval Kit module enables UART data transmission via WiFi, ultra low power consumption, encrypted communication

E-Ink display (ePaper) with a diagonal of 2.9 "and a resolution of 296 x 128 pixels with a SPI controller. Waveshare 2.9inch e-Paper (B)

Waveshare Photo Interrupter Sensor is an IR optical sensor module with Schmitt trigger and a signaling diode allowing the construction of an incremental encoder. Waveshare Photo Interrupter Sensor

MIC5504-3.3YM5, Single Output LDO 3,3V 300mA, SOT23-5

The S9V11F3S5CMA switching step-up/step-down regulator efficiently produces a fixed 3.3 V (default) or 5 V (selectable) output whether it is higher or lower than the input voltage, which can range from 2 V to 16 V. (Note: minimum start-up voltage is 3 V, but it operates to 2 V after that.)

Shielded FTP category 6 Ethernet network cable with RJ45 plugs. Lanberg PCF6-10CC-1000-W

Pololu Dual G2 High-Power Motor Driver 18v22 is an extension that allows you to control two DC motors designed for Raspberry Pi. The motors can be powered with 6.5-30V and draw up a maximum current of 22A. Pololu 3754

Pololu Dual G2 High-Power Motor Driver 24v18 is an extension that allows you to control two DC motors designed for Raspberry Pi. The motors can be supplied with 6.5-36V voltage and can draw a maximum current of 18A. Pololu 3756

Pololu Dual G2 High-Power Motor Driver 18v22 is an extension that allows you to control two DC motors designed for Arduino tiles. The motor can be supplied with 6.5 ... 30V voltage and can draw up a maximum current of 22A. Polol 2517

This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 Voperating range and are efficient enough to deliver a continuous 18 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation.