Category: Audio
Subcategories
There are 276 products.
Audio module with DAC, headphone amplifier and display, designed to work with the Raspberry Pi. It is based on the PCM5100A system and communicates via the I2S interface. Pimoroni PIM482
Module with an AB class amplifier based on the Boomer® LM4853 system. It can work in two modes: mono (power 1.5 W, load 4 Ω) or stereo (power 300 mW, load 8 Ω). It has a potentiometer for power control and gain control for the left and right channel. SparkFun DEV-14475
WM8960 stereo codec module with driver for 1W class D speakers and headphones. It uses the I2S interface and the I2C bus to configure the system. SparkFun BOB-21250
Class A power amplifier with one channel (mono) with the power of 10 W. Built on the popular design of J. Hood from 1969.
Class D digital audio amplifier with Bluetooth module. It has two channels with a power of 50 W and can work with speakers from 4 to 8 Ω. It is powered with the voltage in the range from 9 to 24 V. NS-01G
Module with audio amplifier and 8 Ω speaker with a power of 1 W. The board is equipped with a STEMMA connector. Adafruit 3885
Audio receiver with Bluetooth 5.0 communication based on the QCC3008 module. It can be powered with the voltage from 3.6 V to 5.5 V, including with a lithium battery
Module with a passive buzzer designed for M5Stack sets. It is equipped with a Grove connector and is controlled by a square signal. M5Stack U132
2-channel stereo audio mixer in a metal housing. It has four outputs, on which the summed signal from 2 inputs is available. It is powered with the voltage from 5 to 19 V
PAM8302 Class D mono digital audio amplifier module. The system allows you to connect one loudspeaker with an impedance of 4 to 8 Ω and a power of 2.5 W. The board is equipped with a STEMMA connector. Adafruit 5647
4-channel stereo audio mixer module. It has one output to which the summed signal from 4 inputs comes out. It is powered with the voltage from 5 to 12 V
MEMS SPU0414HR5H-SB analog microphone module. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020852
Stereo audio amplifier with Bluetooth 5.0 communication. It can be powered with the voltage from 9 to 24 V and has two outputs with a power of 50 W. Assembly kit. ZK-502C
The module with a digital stereo audio amplifier is equipped with Bluetooth communication. The system allows you to connect two speakers with an impedance of 6 Ω or 8 Ω with a power of 6 W per channel
LM386 audio amplifier module in a set with a loudspeaker. The board is equipped with a Grove connector and is controlled by a PWM signal. Seeed Studio 101020853
Audio receiver with Bluetooth 4.2 module. It is powered by a microUSB connector or a battery and is equipped with a charging circuit
Analog audio level indicator in the form of a panel meter. Powered with AC or DC voltage from 6 to 12 V, it has a built-in green backlight
Module with a sound sensor based on an electret microphone and LM358 amplifier. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020023
Class D digital audio amplifier with Bluetooth module. It has two channels with a power of 50 W and can work with speakers from 4 to 8 Ω. It is powered with the voltage in the range from 9 to 24 V. NS-01G
Module for recording sounds, which can store recordings up to 20 seconds. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 107020007