![Dwukanałowy sterownik silników DC (2 x 7 A) Dwukanałowy sterownik silników DC (2 x 7 A)](https://kamami.pl/27923-large_default/2x7a-dc-motor-driver.jpg)
![Dwukanałowy sterownik silników DC (2 x 7 A) Dwukanałowy sterownik silników DC (2 x 7 A)](https://kamami.pl/27923-large_default/2x7a-dc-motor-driver.jpg)
zł82.36 tax excl.
Ultra small Dual DC motor driver for some room limited projects. UVLO (Under Voltage Latch-Out) features a safe guard for your system. DRI0041
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
This is an ultra small Dual DC motor driver for some room limited projects. UVLO (Under Voltage Latch-Out) features a safe guard for your system. It is very considerate to own an Photo Coupler isolation for all the signals in case of that the motor's Reverse Current would interfere the control signals. Besides all, all the interfaces includes ESD (electro-static discharge) protection.
Data sheet
Brush DC motor with permanent magnets in housing 130
This compact expansion board plugs directly into the GPIO header on a Raspberry Pi B+, A+, or Pi 2 and provides an easy and low-cost solution for driving a pair of small brushed DC motors. Pololu 2753
No product available!
Ultra small Dual DC motor driver for some room limited projects. UVLO (Under Voltage Latch-Out) features a safe guard for your system. DRI0041
No product available!
Module with DC motor driver DRV8876. It can work with motors supplied with the voltage from 4.5 to 37 V and the current consumption up to 1.3 A. Pololu 4036
The Tic T834 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC).
TB67S249FTG Stepper Motor Driver Compact Carrier (Header Pins Soldered)
Compact stepper motor controller with the TMC2208 system with operating voltage from 4 to 35 V. It offers smooth, quiet operation, high efficiency, various operating modes and easy configuration. It is controlled via the STEP/DIR interface and is an ideal solution for 3D printers and similar applications
No product available!
RC type ESC controller module dedicated to DC brushed motors with a supply voltage from 4.2 V to 8.4 V and a current consumption of up to 3 A
No product available!
Module with two DRV8830 DC motor drivers. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 105020010
Pololu Simple Motor Controller 18v7 (Fully Assembled)
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 V operating range and are efficient enough to deliver a continuous 18 A without a heat sink.
Pololu Simple High-Power Motor Controller 18v25
No product available!
The DC motor driver module enables the motor to be controlled using a PWM signal with several supply voltages (3V, 6V, 12V, 24V and 35V) and a maximum continuous current of 5A.
Pololu Simple High-Power Motor Controller 24v12 (Fully Assembled)
Advanced, compact stepper motor driver with TMC2209 chip that offers smooth, quiet operation, high performance, various operating modes and easy configuration, ideal for 3D printers and other applications. modTMC2209v4
This compact breakout board for Maxim’s MAX14870 motor driver offers a wide operating voltage range of 4.5 V to 36 V and can deliver a continuous 1.7 A (2.5 A peak) to a single brushed DC motor. It features a simple two-pin speed/direction interface and built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature.
Stepper motor driver that can work with a voltage in the range from 20 to 50 V and a maximum current of 5.6 A. It allows you to configure the microstep in the range from 2 to 128. DM556
No product available!
Module with a stepper motor driver based on the DRV8834 system. It allows you to power a bipolar motor with a current of up to 2 A per phase, without using a heat sink. The system can be powered with a voltage of up to 10.8 V. Pololu 2134
Ultra small Dual DC motor driver for some room limited projects. UVLO (Under Voltage Latch-Out) features a safe guard for your system. DRI0041