 
        
           
        
          The module contains a digital temperature and relative humidity sensor operating in the range of 10 to 90% RH. The built-in HIH6130-021-001 (Honeywell *) system with I2C interface allows reading data with 14-bit resolution and has the ability to set an alarm, activated after exceeding a specified measurement threshold. The configuration jumper V_SEL +3,3 V / + 5 V enables selection of supply voltage and digital signals.
Attention!
The standard setting of the power jumper is +3.3 V.
Modulowo® DuoNect ™ solution
The Modulowo® DuoNect ™ solution enables fast and easy connection of expansion modules to Arduino , Raspberry Pi , Intel® Edison , STM32 Nucleo , Atmel Xplained , TI LaunchPad , Freescale Freedom and other platforms.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Gravity: High Accuracy is a multifunctional environmental sensor with Gravity I2C and UART output. Perfect for weather station projects. DFRobot SEN0501
Module with DHT20 sensor. It allows you to measure humidity in the range from 0 to 100% and temperature from -40 to 80 ℃. Seeed Studio 101020932
High-end temperature and humidity sensor module, offering ±1.0% RH and ±0.1°C precision and full I2C communication. With 3.3 to 5V voltage compatibility, STEMMA QT connectors and IP67 protection, it is easy to integrate and resistant to harsh environmental conditions. Ideal for IoT projects, weather stations and automation systems requiring accurate measurements. Adafruit 6174
 No product available!
Module with a BME680 sensor that allows you to measure temperature, humidity, pressure and gas detection. The board is equipped with a Grove connector and communicates via I2C and SPI. Seeed Studio 101020513
Module with a digital temperature and humidity sensor based on the SHT30. Communication via the I2C interface. DFRobot SEN0330
Digital temperature and humidity sensor with calibrated digital output signal. Equipped with a 2.5 mm 4-pin male stereo audio connector that works perfectly with the Sonoff TH10/TH16 socket. Sonoff Si7021
A digital temperature and humidity sensor module based on the SHT45 chip. It features a STEMMA QT/Qwiic connector and communicates via an I2C interface. Adafruit 5665
 No product available!
A module with a temperature and humidity sensor based on the AHT20 system. It communicates via the I2C interface. DFRobot SEN0527
 No product available!
The module has a humidity sensor (accuracy ± 2% RH) and temperature with an accuracy of ± 0.3 ° C. Communication takes place via the I2C bus
Module with a digital temperature and humidity sensor based on the SHT35. Communication via the I2C interface. DFRobot SEN0333
A module with an AHT20 industrial grade temperature and humidity sensor. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101990644
Module with a digital temperature and humidity sensor based on the SHTC3 system. Communication takes place via the I2C interface. DFRobot SEN0414
Module with BME280 environmental sensor. It allows you to measure temperature, humidity and pressure. The sensor is equipped with two communication interfaces: SPI and I2C (Qwiic). SparkFun SEN-15440
Module with a digital temperature and humidity sensor based on the SHT31-F system. Communication via the I2C interface. Equipped with a Gravity DFRobot SEN0334 connector
Temperature and humidity sensor module based on the HTS221 chip. Equipped with a STEMMA QT connector, it communicates via an I2C or SPI interface. Adafruit 4535
Temperature and humidity sensor SHT20 closed in a waterproof housing. Communication via the I2C interface. DFRobot SEN0227
 
                    Temperature and relative humidity sensor, equipped with HIH6130-021-001 system with I2C interface. MOD 68