SHT20 I2C Temperature & Humidity Sensor - waterproof SHT20 temperature and humidity sensor
ID: 566222
5902186313156
zł114.75
Tax included
zł93.29 tax excl.
Temperature and humidity sensor SHT20 closed in a waterproof housing. Communication via the I2C interface. DFRobot SEN0227
Description
Temperature and humidity sensor equipped with a waterproof probe. It uses the CMOSens® SHT20 chip and has a built-in amplifier, A / D converter, OTP memory and a digital processor. It is characterized by high reliability and long-term stability. It is equipped with a 10 k pull-up resistor and a capacitor with a 0.1 uF filter, which allows the sensor to be used directly with a microcontroller. It is supplied with the voltage of 3.3 V or 5 V and communicates via the I2C interface. Full documentation with examples of use is available on the product wiki page.
Features
- Humidity measuring range: 0 to 100% RH
- Temperature measuring range: -40 to 125 ℃
- Communication interface: I2C
- Protection class: waterproof
- Relative humidity response time: 8 s
- Accuracy: ± 3% RH, ± 0.3 ℃
- Voltage: 3.3 / 5V
- Dimension: 73 x 17 mm
- Weight: 44 g
Kit contains
- SHT20 I2C Temperature & Humidity sensor
- 4 x F-F connecting cable
566222
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł22.82
24h
Available quantity: 1
Available
Module 4-pin sensor adapter. DFRobot FIT0511
zł13.87
24h
Available quantity: 3
Available
Other products in the same category (16)
Module with temperature and humidity sensor DHT11. It uses a 1-wire communication interface and has a humidity measurement range from 20 to 90% with an accuracy of 5% and temperature from 0 to 50 ºC with an accuracy of 2 ºC
zł17.20
24h
Available quantity: 1
Available
KAmodHTS221 is a module that allows the measurement of humidity and temperature, and thanks to the built-in stabilizer and translator levels, it can be successfully used in systems supplied with a voltage of 2.5 - 5.5 V
zł34.90
24h
Available quantity: 219
Available
The module has a humidity sensor (accuracy ± 2% RH) and temperature with an accuracy of ± 0.3 ° C. Communication takes place via the I2C bus
zł28.01
24h
Available quantity: 8
Available
High-end temperature and humidity sensor module, offering ±1.0% RH and ±0.1°C precision and full I2C communication. With 3.3 to 5V voltage compatibility, STEMMA QT connectors and IP67 protection, it is easy to integrate and resistant to harsh environmental conditions. Ideal for IoT projects, weather stations and automation systems requiring accurate measurements. Adafruit 6174
zł67.97
24h
Available quantity: 1
Available
Temperature and humidity sensor module based on the HTS221 chip. Equipped with a STEMMA QT connector, it communicates via an I2C or SPI interface. Adafruit 4535
zł57.90
24h
Available quantity: 3
Available
Module with BME680 for measuring the concentration of VOC, pressure, temperature and humidity. Equipped with a STEMMA QT connector, it communicates via I2C or SPI. Adafruit 3660
zł105.20
24h
Available quantity: 1
Available
Module with temperature, humidity and pressure sensor BME680 from Bosch. The module communicates via I2C or SPI interfaces.
zł45.77
24h
Available quantity: 19
Available
Wireless sensor with LoRaWAN network communication. Dedicated to industrial long-distance data acquisition with a wide measurement range of temperature from -40°C to 85°C and humidity from 0 to 100% RH. Seeed Studio 114992867
zł341.89
24h
Available quantity: 3
Available
Module with SHT31 temperature and humidity sensor. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020212
zł52.95
24h
Available quantity: 2
Available
Module with a steam sensor. It can be supplied with the voltage of 3.3 V or 5 V. It has an analog output. DFRobot SEN0121
zł6.21
24h
Available quantity: 5
Available
Module with a temperature and humidity sensor based on the SHT40 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4885
zł28.55
24h
Available quantity: 4
Available
Module with SHT35 temperature and humidity sensor. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 101020592
zł63.76
24h
Available quantity: 1
Available
Module with pressure, temperature and humidity sensor BME280. It allows to read the atmospheric pressure in the range from 300 to 1100 hPa and communicates via the I2C or SPI interface. Waveshare BME280 Environmental Sensor
zł42.00
24h
Available quantity: 11
Available
Integrated BME688 gas, pressure, temperature and humidity sensor in one MEMS housing. The system can be supplied with the voltage of 3.3 V and is equipped with an I2C communication interface. BME688 Breakout Board
zł161.54
24h
Available quantity: 2
Available
Module with a BME680 sensor that allows you to measure temperature, humidity, pressure and gas detection. The board is equipped with a Grove connector and communicates via I2C and SPI. Seeed Studio 101020513
zł110.07
24h
Available quantity: 3
Available
Adafruit module with Si7021 temperature and humidity sensor. Sensor Sillicon Labs can measure temperature in the range of -10 ~ 125 ° C, and humidity in the range of 0-100 & RH. The sensor communicates using the I2C interface. Adafruit 3251
zł51.20
24h
Available quantity: 1
Available
Temperature and humidity sensor SHT20 closed in a waterproof housing. Communication via the I2C interface. DFRobot SEN0227