zł25.20 tax excl.
Analogue temperature and humidity sensor module based on SHT30 sensor. It is characterized by high reliability and stability with low energy consumption. It is compatible with 3.3V and 5V controllers, such as Arduino, micro:bit, ESP32. DFRobot DFR0588
Analogue temperature and humidity sensor module based on the SHT30 sensor from Sensirion. It is characterized by high reliability and stability with low energy consumption, fast response and resistance to interference. The sensor is internally calibrated and amplified to obtain analog output voltages that are linear with respect to temperature or humidity. It is compatible with 3.3 V and 5 V controllers, such as Arduino, micro:bit, ESP32.
.jpg)
Manufacturer
Responsible person
Gravity: Analog Signal Isolator is a module that allows to isolate sensors in the system and eliminate mutual interference of sensors powered by 5V. DFRobot DFR0504
No product available!
Gravity: I2C 12-Bit DAC is a module with 12-bit DAC and built-in EEPROM memory. The module is powered by 3.3 ... 5V for communication used by the I2C interface. DFRobot DFR0552
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553
No product available!
Gravity: Digital 10A Relay Module is a module with 10A 35VAC / 30VDC relay compatible with devices with control signals in the range of 2.8 ... 5.5V. DFRobot DFR0473
Gravity: Formaldehyde (HCHO) Sensor is a module for measuring the concentration of formaldehyde (methane) in the air. It can be supplied with voltage in the range of 3.3 ... 6V. DFRobot SEN0231
Module of the 3-axis LIS2DH, I2C accelerometer. DFRobot SEN0224
Gravity I2C OLED-2864 Display is an OLED display with I2C interface with 128x64 resolution, powered by 3.3-5V. DFRobot DFR0486
No product available!
Nano I / O Shield for Arduino Nano is an expansion board for Arduino Nano that provides digital, analog pins, power inputs and a connector for the Bluetooth module. DFRobot DFR0012
BME280 integrates onboard temperature sensor, humidity sensor and barometer. It provides both SPI and I2C interfaces; and can be widely used in environmental monitoring, story height measurement and Internet of Things (IoT) control and so on. SEN0236
DFRobot 315MHz RF receiver module using SC2272-L4 low power decoder chip. DFRobot TEL0112
DFR0464
Gravity: I2C VEML7700 Ambient Light. Sensor SKU. SEN0228
Gravity Colorful LED is an LED twinkles with seven colors--the colors of rainbow. DFRobot DFR0474
Clock & Timer Development Tools Gravity I2C SD2405 RTC. DFR0469
Gravity: Analog Signal Isolator is a module that allows to isolate sensors in the system and eliminate mutual interference of sensors powered by 5V. DFRobot DFR0504
No product available!
Module 4-pin sensor adapter. DFRobot FIT0511
Measurement module for dissolved oxygen in water. It allows you to determine the level of water quality. The set includes a measuring module and a probe. DFRobot SEN0237-A
Expansion board for micro:bit modules with connectors compatible with Boson and Gravity sets. DFRobot DFR0521
Audio Analyzer is a module with sound analyzer based on the MSGEQ7 system. It divides the sound into seven frequency bands, and then allows you to read the peak levels of each band. It allows you to measure the sound in the following frequencies: 63Hz, 160Hz, 400Hz, 1kHz, 2.5kHz, 6.25kHz and 16kHz. DFRobot DFR0126
Analogue temperature and humidity sensor module based on SHT30 sensor. It is characterized by high reliability and stability with low energy consumption. It is compatible with 3.3V and 5V controllers, such as Arduino, micro:bit, ESP32. DFRobot DFR0588