Plantower PMS3003 - laser dust sensor
ID: 563980
5906623455942
zł95.25
Tax included
zł77.44 tax excl.
Laser sensor of air pollution with particles PM1,0, PM2.5 and PM10. It allows for precise analysis of the amount of pollutants in the environment, has small dimensions and a built-in silent transfer fan. Data is output to the UART interface. PMS3003
Description
Laser sensor of air pollution with particles PM1.0, PM2.5 and PM10. It allows for precise analysis of the amount of pollutants in the environment, has small dimensions and a built-in silent transfer fan. Data is output to the UART interface.
properties
- Laser particle concentration sensor PM2.5 in the air
- Work scope (PM):
-
- 0.3 μm - 1.0 μm
- 1.0 μm - 2.5 μm
- 2.5 μm - 10 μm
- Built-in fan that takes air samples
- UART interface
- Power supply: 5 V
- Interface voltage: 3.3 V
- Power consumption (maximum): 120 mA
- Power consumption (sleep mode): <200 uA
- Working temperature range: -10 ~ 60 ° C
- Small dimensions: 65 x 42 x 23 mm
- Weight: 35 g
Description of leads
Attention!
The voltage on the RX, TX, RESET, SET signal lines must not exceed 3.3 V. If you want to control the module with a higher voltage, we recommend using a logic converter, eg KAmodLVC .
The sensor is protected with a blue foil. The foil has only a protective role.
| Contact | Name | Description |
|---|---|---|
| 1 | VCC | + 5V |
| 2 | GND | Mass |
| 3 | SET | Sleep (when low) |
| 4 | RXD | Data collection line |
| 5 | TXD | Data transmission line |
| 6 | RESET | Resetting (when low) |
| 7 | NC | - |
| 8 | NC | - |
Included
- Plantower PMS3003 dust sensor module
- JST cable with isolated terminals
To download
563980
Data sheet
- Interface
- UART
- Type of sensor
- inny
- Power supply voltage
- 5 V
- Concentration measurement
- PM1.0/PM2.5/PM10
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Available
PMS7003 is a kind of digital and universal particle concentration sensor, which can be used to obtain the number of suspended particles in the air, i.e. the concentration of particles, and output them in the form of digital interface
zł107.07
Delivery date unknown
No product available!
Laser sensor of air pollution with particles PM1,0, PM2.5 and PM10. It allows for precise analysis of the amount of pollutants in the environment, has small dimensions and a built-in silent transfer fan. Data is output to the UART interface. Planter PMSA003-C
zł94.89
Delivery date unknown
No product available!
Other products in the same category (16)
Module with gas sensor designed to monitor indoor air quality. It was based on the AMS CCS811 system that allows the detection of volatile organic compounds (VOCs) in the air. Digilent 410-386
zł174.70
24h
Available quantity: 1
Available
Air quality sensor module based on the SGP40 system. It uses CMOSens technology by Sensirion and provides information on the concentration of volatile organic compounds (VOC). Adafruit 4829
zł74.80
24h
Available quantity: 2
Available
The sensor is designed for indoor air quality testing. The main gas detected is carbon monoxide, alcohol, acetone, thinner, formaldehyde and other slightly toxic gases. It is compatible with 5V and 3.3V power supply. Seeed Studio 101020078
zł58.12
24h
Available quantity: 3
Available
A sensor used to detect air pollutants by measuring VOCs and gases such as ammonia or hydrogen sulfide. It is used in various areas, such as the food industry, chemical industry, air quality control in laboratories and environmental monitoring. Figaro TGS2602
zł31.33
24h
Available quantity: 14
Available
Module with PM2.5 dust sensor. The board is equipped with a Gravity connector and communicates via the I2C interface. DFRobot SEN0460
zł202.34
24h
Available quantity: 1
Available
Indoor air quality measurement module, combining two high-end Sensirion sensors – SCD41 and SEN55. It offers a comprehensive set of measurements, including CO2 concentration, volatile organic compounds (VOC), suspended dust (PM1.0, PM2.5, PM4, PM10), as well as temperature and relative humidity. SparkFun SEN-25200
zł709.81
3 weeks
No product available!
ENS160 gas sensor module to measure the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via an I2C or SPI interface. SparkFun SEN-20844
zł119.84
24h
Available quantity: 3
Available
The module allows the detection of volatile organic compounds (VOC) in the air, based on Winsen\'s WSP2110 system. Allows for detection in the air; formaldehyde (HCHO), methane, benzene, toluene, alcohol, etc. The sensor output is an analog signal. Seeed studio 101020001
zł79.32
24h
Available quantity: 4
Available
Laser sensor of air pollution with particles PM1,0, PM2.5 and PM10. It allows for precise analysis of the amount of pollutants in the environment, has small dimensions and a built-in silent transfer fan. Data is output to the UART interface. Planter PMSA003-C
zł94.89
4 weeks
No product available!
Air quality sensor module based on the ENS160 system. It communicates via the I2C or SPI interface. DFRobot SEN0515
zł67.69
24h
Available quantity: 5
Available
Module with environmental sensors for Raspberry Pi Pico. It allows you to measure temperature, humidity, air quality pressure and color detection. SB Components 22366
zł208.80
24h
Available quantity: 3
Available
Laser sensor of air pollution with PM2,5 and PM10 particles. It allows for precise analysis of the amount of pollutants in the environment, has small dimensions and a built-in silent transfer fan. The data is output to the UART interface and via the PWM signal. Nova Fitness SDS018
zł147.14
24h
Available quantity: 2
Available
BME688 integrated gas, pressure, temperature and humidity sensor module in a single MEMS housing. It is equipped with an I2C and SPI interface. It has built-in AI functions. Waveshare BME688 Environmental Sensor
zł101.32
24h
Available quantity: 3
Available
Module with PM2.5 HM3301 dust sensor. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020613
zł150.23
24h
Available quantity: 1
Available
PMS7003 is a kind of digital and universal particle concentration sensor, which can be used to obtain the number of suspended particles in the air, i.e. the concentration of particles, and output them in the form of digital interface
zł107.07
4 weeks
No product available!
An optical particle sensor that uses laser scattering and Sensirion\'s innovative contamination resistance technology. It enables users to measure mass concentration and particle number. SparkFun SEN-15103
zł179.00
24h
Available quantity: 2
Available
Laser sensor of air pollution with particles PM1,0, PM2.5 and PM10. It allows for precise analysis of the amount of pollutants in the environment, has small dimensions and a built-in silent transfer fan. Data is output to the UART interface. PMS3003