Total suspended particulate (TSP) sensor, using principle of laser scattering, can get the particle concentration between 1 to 100μm in the air. The sensor can communicate with the microcontroller via the UART interface or via a configurable output port. The laser diode used in the sensor is of high quality and allows trouble-free operation even for 8000 hours of continuous working, this time can be significantly extended by reducing the frequency of measurements.
| No. | Name | Comment |
| 1 | NC | Not Connect |
| 2 | 1μm | Reserved |
| 3 | 5V | 5V Input |
| 4 | 2,5μm | Reserved |
| 5 | GND | Ground |
| 6 | R | RX interface UART(TTL)@3.3V |
| 7 | T | TX interface UART(TTL)@3.3V |
Data sheet
Manufacturer
Responsible person
Board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
The latest version of the Raspberry Pi series: Raspberry Pi 4 model B with quad-core SoC (Broadcom BCM2711, Cortex-A72) working at 1.8GHz, 2GB RAM LPDDR4, Broadcom VideoCore VI.
The long-awaited Raspberry Pi 4 model B with the SoC Broadcom BCM2711 (4 x Cortex-A72) running at 1.8 GHz, 3 GB LPDDR4 RAM and the Broadcom VideoCore VI graphics chip
Development board with SAMD21 microcontroller (ARM Cortex® M0+), 8 I/O lines, 12 PWM channels, micro-USB. The board is equipped with an ESP32 module enabling the implementation of communication via WiFi. Arduino MKR WiFi 1010 ABX00023
No product available!
Board with nRF52840 microcontroller with Cortex M4F core (64 MHz, 1 MB Flash, 256 kB RAM). Equipped with BT 5.0 and IMU LSM9DS1 module. Module with headers. Arduino ABX00034
Laser sensor of air pollution with PM2,5 and PM10 particles. It allows for precise analysis of the amount of pollutants in the environment, has small dimensions and a built-in silent transfer fan. The data is output to the UART interface and via the PWM signal. Nova Fitness SDS018
Module with SGP30 gas sensor. The sensor communicates via the I2C interface. SGP30 system contains several elements reacting to various metal oxides, which allows for more accurate determination of air quality. Adafruit 3709
Module with gas sensor designed to monitor indoor air quality. It was based on the AMS CCS811 system that allows the detection of volatile organic compounds (VOCs) in the air. Digilent 410-386
PM2.5 dust sensor powered by 5V, communication via the UART interface. Sharp GP2Y1051AU0F
Total suspended particulate (TSP) sensor that allows you to measure the particle concentration from 1 to 100 μm. SDS198
Air quality sensor module based on SGP30 system. The board has been equipped with Qwiic connectors. SparkFun SEN-16531
Module with sensors of environmental parameters. It allows you to measure temperature, humidity and pressure as well as CO2 and VOC concentration. DFRobot SEN0335
Sharp GP2Y1010AU0F dust and particle concentration sensors. It is supplied with the voltage from 5 to 7V. Has an analog output. DFRobot SEN0144
Module with PM2.5 HM3301 dust sensor. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020613
Module with air quality sensor SGP30. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020512
No product available!
Air quality sensor module based on the SGP40 system. It communicates via the I2C interface. DFRobot SEN0392
Module with air quality sensor SGP30. It allows you to read the concentration of VOC (TVOC) and eCO2 and communicates via the I2C interface. Pimoroni PIM480
Air quality sensor module PMSA003I. It allows for a precise analysis of the amount of pollutants in the environment based on the concentration of PM1.0, PM2.5 and PM10 particles. Adafruit 4632
Air quality sensor module based on the SGP40 system. It uses CMOSens technology by Sensirion and provides information on the concentration of volatile organic compounds (VOC). Adafruit 4829
Module with PM2.5 dust sensor. The board is equipped with a Gravity connector and communicates via the I2C interface. DFRobot SEN0460
Module with environmental sensors for Raspberry Pi Pico. It allows you to measure temperature, humidity, air quality pressure and color detection. SB Components 22366
Total suspended particulate (TSP) sensor that allows you to measure the particle concentration from 1 to 100 μm. SDS198