KAmodRGB
ID: 136028
5906623432301
zł47.90
Tax included
zł38.94 tax excl.
Programmable RGB and RGBA LED driver
Programmable RGB and RGBA LED driver module
KAmodRGB can extend any device equipped with I2C interface with programmable 4-channel LED driver. It can be used for RGB and RGBA LEDs.
Basic features:
- 4-channel LED driver – PCA9633 by NXP
- I2C interface (also Fm+)
- 5-channel PWM generator with 8-bit resolution on every channel
- Programmable PWM frequency: 190Hz or 0.09…24Hz
- Duty cycle 0…99.6%
- Configurable LED output (open-drain or totem-pole)
- 25mA sink capability
- Configurable I2C address (8 combinations)
- 5V compatible I/O lines
- Supply voltage 2,3...5,5VDC (5V recommended)
- Built-in RGB LED and additional LED
- I2C Kamami standard connector (compatible with most of Kamami evaluation boards)
- Dimensions: 30 x 45 x 15 mm
Standard equipment:
- Assembled module
136028
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Cables for evaluation boards, set of 10 pcs., blue colour
zł5.20
24h
Available quantity: 136
Available
Cables for evaluation boards, set of 10 pcs., red colour
zł5.20
24h
Available quantity: 99
Available
Cables for evaluation boards, set of 10 pcs., green colour
zł5.46
24h
Available quantity: 320
Available
A 30 cm long connecting cable (4 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF04S connector that KAmod modules are equipped with. cabhu04-30
zł6.90
24h
Available quantity: 3
Available
Cables for evaluation boards, set of 10 pcs., yellow colour
zł5.61
24h
Available quantity: 39
Available
Cables for evaluation boards, set of 10 pcs., white colour
zł6.06
24h
Available quantity: 19
Available
Set of 40 pieces of male-female connection cables, in various colors, 17 cm long. CAB_M-F (Rainbow-40-17)
zł5.97
24h
Available quantity: 32
Available
Other products in the same category (16)
zł5.90
24h
Available quantity: 480
Available
KAmodMMA8451Q is a module with the MMA8451Q three-axis accelerometer from NXP. The sensor allows the measurement of acceleration in the range of ±2g/±4g/±8g, the measurement frequency is from 1.56 Hz to 800 Hz. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMMA8451Q
zł24.90
24h
Available quantity: 233
Available
KAmodMPC17C724 is a module with a double MP bridge bridge type MPC17C724. The system allows you to control two DC brush motors or one bipolar stepping motor. The controller operates at a voltage range of 2.7 - 5.5 V and can work with motors with power consumption up to 0.4 A.
zł19.90
24h
Available quantity: 336
Available
KAmodMC3635 is a module with the MC3635 three-axis accelerometer from mCube. The sensor allows the measurement of acceleration in the range of ±2g/±4g/±8g/±12g/±16g, the measurement frequency is from 14 to 1300 Hz. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMC3635
zł14.90
24h
Available quantity: 453
Available
KAmodBT-HC05 is a Bluetooth module configured via AT commands. It has integrated LEDs indicating operating mode and connection status with the paired device, as well as a logic level translator on UART lines. KAmodBT-HC05
zł49.90
24h
Available quantity: 74
Available
KAmodM41T82 is a module with the STMicroelectronics M41T82 RTC clock. The chip allows precise timing, and an additional battery connector allows you to maintain the power supply when the main power is turned off. Communication with the module is realized via I2C bus.
zł31.49
24h
Available quantity: 463
Available
Relay output module for Raspberry Pi 4B, Pi 3B+ Pi3B, Pi2, Pi+, Pi minicomputers.
zł49.00
24h
Available quantity: 140
Available
Pressure sensor module with I2C interface (MPL115A2)
zł44.90
24h
Available quantity: 19
Available
Available
Available
KAmodL3GD20 is a digital gyroscope module with L3GD20 chip. It makes possible to measure angular velocity up to ± 2000 degrees per second. It has a embedded voltage regulator and level translators on SDA/SCL lines, thanks to which it can be used in systems supplied with a voltage of 2.5 V-5.5 V. KAmodL3GD20
zł39.90
24h
Available quantity: 100
Available
KAmodPCF8883T is a module with capacitive touch sensor PCF8883 from NXP. The module has a probe placed on the PCB and a diode indicating the state of the chip. It enables work in one of three modes.
zł19.90
24h
Available quantity: 431
Available
KAmodMPL3115A2 is a module with an atmospheric pressure sensor MPL3115A2 from NXP. Sensor allows to make a measurement in the range of 200...1100hPa (20...110kPa). Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMPL3115A2
zł27.90
24h
Available quantity: 192
Available
KAmodLSM6DS3 is a module that allows measurement of acceleration and angular velocity values. It has a built-in voltage stabilizer and level translators on SDA / SCL lines, thanks to which it can be used in 2.5-5.5V voltage systems
zł27.48
24h
Available quantity: 119
Available
KAmodLPS25HB is a module that allows the measurement of atmospheric pressure in the range of 260-1260hPa with a resolution of 0.01hPa, and thanks to the embedded regulator and voltage translator levels, it can be successfully used in systems supplied with a voltage of 2.5 - 5.5 V.
zł40.90
24h
Available quantity: 184
Available
KAmodMMA7361LC is an accelerometer module with an analogue output, equipped with the MMA7361LC chip. It has a embedded voltage regulator, so it can be used in systems supplied with voltage of 2.5...5.5V.
zł28.91
24h
Available quantity: 192
Available
Programmable RGB and RGBA LED driver