

Key Features:
Download:
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
USB to TTL Serial Cable - Debug / Console Cable for Raspberry Pi, RoHS
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. DEV-09716
No product available!
With an integrated ESP8266 WiFi controller this module is a one-stop shop for almost any Internet-connected project. Firmware can be developed in Arduino and uploaded over a simple, serial interface. WRL-13711
CP2102 USB to UART Module, USB micro connector
UART - USB converter based on the FT232RL chip with TX, RX, RTS and CTS lines led out to the pin connector, the remaining lines available on solder fields for pin connectors. Micro-USB socket. Voltage supply from 3.3 to 5 V. FT232 USB UART Board (micro)
USB TO UART solution with USB Type A connector
ZL5USB is a USB-UART converter module based on Silabs CP2102. The module has small sizes, microUSB connector and it can works with the 2.5...5.5V signals.
The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. The power pin provides the 5V @ 500mA direct from the USB port and the RX/TX pins are 3.3V level for interfacing with the most common 3.3V logic level chipsets. Adafruit 954
Easy-to-use USB-to-Serial adapter based on the CH340G IC from WCH; works with 5V and 3.3V systems and should auto install on most operating systems without the need for additional drivers; uses the CH340G IC to quickly and easily convert serial signals to USB. DEV-14050
The CY7C65213 USB to UART serial breakout is designed to provide users with a means to access all available I/O pins on the IC, and to provide a 6-pin UART header that is compatible with other SparkFun breakout boards. This breakout has a microUSB connector and other support circuitry to get the IC quickly up and running. BOB-13830
USB - UART converter based on the PL2303 chip. Compatible with voltages of 1.8 V, 2.5 V, 3.3 V and 5 V, it is equipped with a USB type C connector. Waveshare PL2303 USB UART Board (Type C)
No product available!
USB-UART converter for Odroid minicomputers. It is based on the CP2102N chip and is equipped with a USB type C connector
Pmod SSR is a module with a semiconductor relay. One GPIO port is required for control, the relay is suitable for operation with up to 48 V, it can be used for devices that draw current up to 6 A. Digilent 410-342
No product available!
The Digilent Pmod COLOR is a color sensor module with the ability to sense red, green, blue and clear light. Digilent 410-348
No product available!
PmodCMPS2 is a module with a digital magnetometer based on the Memsic MMC34160PJ system. It has a resolution of 0.5 mG (within ± 16) and accuracy up to 1 °. For communication with the module, an I2C interface is provided on the 6-pin Pmod connector. Digilent 410-355
No product available!
The Pmod SF3 provides users with 32 MB of non-volatile memory through the use of Micron\'s NOR Flash memory (N25Q256A). By using the SPI protocol, users can both write to and read from the flash memory. Digilent 410-340
No product available!
The Pmod CAN is a CAN 2.0B controller with an integrated transceiver. The embedded Microchip MCP25625 chip connects directly to the physical CAN bus and meets automotive requirements for high-speed (1 Mb/s), low quiescent current, electromagnetic compatibility, and electrostatic discharge. Digilent 410-353
No product available!
The Pmod BLE module is a Bluetooth module with powerful capabilities. Thanks to communication via the UART port, the module can be connected to any platform equipped with this interface. The module is equipped with the Roving Networks RN4870 system, in which a full Bluetooth interface is built-in. Digilent 410-359
Accessory board designed to provide students a cost-effective, portable, and engaging platform for teaching electronics. With a myDAQ / myRIO, NI Multisim, and a myDigital, you\'ll have everything needed to allow students to design, construct, test basic analog and digital designs. 6002-410-006
No product available!
No product available!
No product available!
Pmod VGA is a module in the VGA video output for development boards equipped with a Pmod connector. With its help, it is possible to display the image on monitors that have a VGA input. Digilent 410-345
No product available!