.png)
BME280 Temperature Humidity & Pressure Sensor - Soldered
ID: 1208258
732388672806
zł50.71
Tax included
zł41.23 tax excl.
BME280 environmental sensor module for measuring temperature from -40 to 80°C, relative humidity from 0 to 100%, and atmospheric pressure from 30 to 110kPa. It communicates via I2C at address 0x76 and features two Qwiic connectors. The board supports 3.3V and 5V power supplies. Soldered 333036
Description
The device Enviromental Sensor BME280 Breakout by Soldered uses the BME280 sensor from Bosch to measure temperature, relative humidity, and atmospheric pressure. The temperature measurement range is -40 to 80°C, the humidity range is 0 to 100%, and the pressure range is 30 to 110kPa. Approximate altitude can also be calculated from the measured atmospheric pressure.
The manufacturer specifies a temperature measurement accuracy of ±1°C, humidity accuracy of ±2%, and pressure accuracy of ±12Pa. Current consumption is approximately 1mA during measurement and less than 5µA while idle. The board can be used in weather stations, environmental data loggers, automation systems, and devices monitoring indoor environmental conditions.
Communication with the microcontroller is handled through the I2C bus at a fixed address of 0x76. In addition to the VCC, GND, SDA, and SCL pins, the board provides 2 Qwiic connectors for solderless connection to compatible systems. The BME280 supports Sleep, Forced, and Normal operating modes, allowing measurement frequency and power consumption to be adjusted to application requirements.
The sensor operates at a 3.3V logic level, while the onboard regulator allows the board to be powered from 3.3V or 5V. Board dimensions are 22 × 22mm. The 3.2mm mounting holes are designed for M3 screws.
Features
- Measurements
- Sensor IC: BME280
- Measured parameters: temperature, relative humidity, atmospheric pressure
- Temperature measurement range: -40 to 80°C
- Temperature measurement accuracy: ±1°C
- Humidity measurement range: 0 to 100%
- Humidity measurement accuracy: ±2%
- Pressure measurement range: 30 to 110kPa
- Pressure measurement accuracy: ±12Pa
- Altitude calculation based on atmospheric pressure
- Communication
- Interface: I2C
- I2C address: 0x76
- Connectors: 2 × Qwiic
- Pins: VCC, GND, SDA, SCL
- Power supply
- Sensor logic level: 3.3V
- Board supply voltage: 3.3V or 5V
- Onboard voltage regulator
- Current consumption during measurement: 1mA
- Idle current consumption: <5µA
- Mechanical parameters
- Board dimensions: 22 × 22mm
- Header pin hole diameter: 1.5mm
- Mounting hole diameter: 3.2mm
- Mounting holes designed for M3 screws
1208258
Data sheet
- Interface
- I2C
- Type of sensor
- BME280
- Power supply voltage
- 3,3 - 5 V
- Sensor type
- Ciśnienia atmosferycznego
Other products in the same category (16)
Module with a BME688 sensor for measuring gas concentration, pressure, temperature and humidity. I2C or SPI communication. SparkFun SEN-19096
zł196.21
24h
Available quantity: 3
Available
Module with digital barometer BMP384. It enables pressure measurement in the range from 300 to 1250 hPa with 24-bit resolution and communicates via I2C or SPI. SparkFun SEN-19662
zł70.47
3 weeks
No product available!
Module with pressure, temperature and humidity sensor BME280. It allows to read the atmospheric pressure in the range from 300 to 1100 hPa and communicates via the I2C or SPI interface. Waveshare BME280 Environmental Sensor
zł50.80
24h
Available quantity: 18
Available
Module with digital barometer BMP388. It enables pressure measurement in the range from 300 to 1250 hPa and communicates via I2C or SPI. Waveshare BMP388 Barometric Pressure Sensor
zł68.63
24h
Available quantity: 4
Available
Module with digital barometer BMP581. It enables pressure measurement in the range from 300 to 1250 hPa with an accuracy of ± 5 Pa and communicates via I2C or SPI. SparkFun SEN-20170
zł114.78
3 weeks
No product available!
Module with digital barometer BMP384. It enables pressure measurement in the range from 300 to 1250 hPa with 24-bit resolution and communicates via I2C. SparkFun SEN-19833
zł91.00
24h
Available quantity: 3
Available
Module with digital barometer BMP581. It enables pressure measurement in the range from 300 to 1250 hPa with an accuracy of ± 5 Pa and communicates via I2C. SparkFun SEN-20171
zł123.77
24h
Available quantity: 1
Available
LPS28DFW absolute pressure sensor module. The chip features a wide measurement range of 260 to 1260 hPa or 260 to 4060 hPa and a high accuracy of 0.5 hPa. It communicates via an I2C interface. SparkFun SEN-21222
zł154.12
24h
Available quantity: 2
Available
LPS28DFW absolute pressure sensor module. The chip features a wide measurement range of 260 to 1260 hPa or 260 to 4060 hPa and a high accuracy of 0.5 hPa. It communicates via an I2C interface. SparkFun SEN-21221
zł117.87
24h
Available quantity: 4
Available
The MS5803-14BA waterproof pressure sensor module. It allows measurement from 0 to 14 bar and communicates via SPI or I2C interface. SparkFun SEN-12909
zł388.99
3 weeks
No product available!
LPS35HW waterproof barometer module. It can measure pressure from 260 to 1260 hPa and communicates via I2C or SPI. Adafruit 4258
zł73.47
24h
Available quantity: 3
Available
BMP390 digital barometer module. Measures pressure from 300 to 1250 hPa and temperature from -40℃ to 85℃. It communicates via an I2C or SPI interface. Waveshare BMP390 Barometric Pressure Sensor
zł117.31
4 weeks
No product available!
LPS22DF digital barometer module. It enables pressure measurement in the range from 260 to 1260 hPa and communicates via I2C or SPI. Pololu 2898
zł46.24
24h
Available quantity: 2
Available
Module with the MS5611 sensor, allowing measurement of atmospheric pressure. The module has a built-in 3.3 V voltage stabilizer. It comes with a connector for self-assembly. modGY-63
zł28.51
4 weeks
No product available!
Gravity: High Accuracy is a multifunctional environmental sensor with Gravity I2C and UART output. Perfect for weather station projects. DFRobot SEN0501
zł142.27
24h
Available quantity: 1
Available
A precise pressure and temperature sensor that supports I2C communication, which makes it easy to integrate with microcontrollers such as Arduino. With its compact design and versatile use in navigation, altitude measurement or GPS assistance, it is ideal for IoT projects and navigation systems. DFRobot SEN0372
zł26.03
24h
Available quantity: 3
Available
BME280 environmental sensor module for measuring temperature from -40 to 80°C, relative humidity from 0 to 100%, and atmospheric pressure from 30 to 110kPa. It communicates via I2C at address 0x76 and features two Qwiic connectors. The board supports 3.3V and 5V power supplies. Soldered 333036