Module with 4-element segment display. Each of the four displays consists of 14 segments, so it can display not only numbers, such as the standard 7-segment display, but also letters and special characters. The display was connected to the VK16K33 controller operating with a voltage from 4.5 V to 5 V, so that when used with Arduino, a voltage level converter is not required. The user can configure the I2C address with two jumpers, which allows you to connect up to 4 such displays on one line. The module communicates via the I2C interface and is supplied with the voltage of 3.3 V. Full documentation with examples of use is available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Module with WiFi and Bluetooth Espressif ESP32 WROOM. It integrates a set of peripheral devices - capacitive touch sensors, Hall sensors, SD card interface, Ethernet, fast SPI, UART, I2S and I2C. SparkFun WRL-15663
Board with the ATmega328 microcontroller from the AVR family, there are 20 I/O lines, 6 PWM channels, 6 analog inputs at the user\'s disposal. SparkFun DEV-15123
Flexible Qwiic cable 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single male goldpin connectors. SparkFun PRT-17912
Flexible Qwiic cable, 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single female goldpin connectors. SparkFun PRT-17261
Module with 4 relays JZC-11F with a load of 5A. It enables switching devices with high power using a microcontroller. I2C communication. SparkFun COM-16566
JST-SH 4-pin SMD connector for modules with Qwiic connectors. Pins\' pitch is 1 mm. Qwiic allows you to connect sensors via the I2C bus. SparkFun PRT-16766
No product available!
Intermediate module of the communication system based on QwiicBus. It allows you to extend the range of the I2C bus. SparkFun COM-18000
Heart rate monitor module based on the popular MAX30101 chip. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-16474
Module with PIR EKMC4607112K motion sensor, power consumption in standby mode up to 170 uA. The board communicates via I2C and is equipped with a Qwiic connector. SparkFun SEN-17374
No product available!
Module with transparent OLED display. It has several display areas with different colors. I2C communication. SparkFun LCD-15079
No product available!
Module with an IO pin expander based on the TCA9534 system. It allows you to add 8 GPIO pins to an I2C-controlled project. SparkFun DEV-17047
Air quality sensor module based on SGP30 system. The board has been equipped with Qwiic connectors. SparkFun SEN-16531
ToF distance sensor (Time of flight) with a range of up to 5 m. The module is supplied with the voltage of 3.3 V and communicates via the I2C interface. SparkFun SEN-19036
Module with relay up to 5.5 A and 240 V AC controlled by the I2C interface. SparkFun COM-15093
Sound module supported by I2C interface, which allows to generate sound signals in simple projects thanks to Qwiic system and ATtiny84 microcontroller. With support of Arduino libraries, users can control volume, frequency and duration of sound, which makes it ideal for applications such as alarms or signals in robots. SparkFun BOB-24474
The expansion module is designed for micro:bit sets. Offers a simple, beginner-friendly robotics controller. SparkFun DEV-15713
GPS module with GNSS receiver ZED-F9P. It can receive data from GPS, GLONASS, Galileo and BeiDou systems. It has USB, UART, I2C and SPI interfaces. RTK and high accuracy up to 10 mm. SparkFun GPS-15136
No product available!
Module with 16-channel PCA9685 servo driver designed for Raspberry Pi minicomputers. The board is equipped with a USB Type C power connector. SparkFun DEV-15316
Air quality sensor module based on the SGP40 system. The board is equipped with Qwiic connectors. SparkFun SEN-18345
Data logger based on the ATmega328 microcontroller. Data received via the I2C interface are saved on the microSD card. The module supports cards with a capacity of up to 32 GB. SparkFun DEV-15164
No product available!
Module with a 4-element 14-segment display. The board is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun COM-16916