zł30.17 tax excl.
RS-485 transceiver module based on the SN65176BDR, designed for bidirectional data transmission between a microcontroller and an RS-485 bus. It supports data rates up to 20Mbps and communication distances up to 1200m, while the onboard 120Ω termination resistor can be enabled using the JP2 jumper. Supply voltage is 5V. Soldered 333068
The device RS-485 Transceiver breakout by Soldered uses the SN65176BDR transceiver for communication between a microcontroller and an RS-485 bus. The IC converts logic signals from the microcontroller into differential bus signals and performs conversion in the opposite direction. Differential transmission increases resistance to interference, allowing the board to be used in automation, control systems, multi-node networks, and industrial installations.
The transceiver supports bidirectional data transmission at rates up to 20Mbps. The manufacturer specifies a communication distance of up to 1200m. Actual data rate and achievable distance depend on factors including cable length and parameters, bus topology, and operating conditions. The A and B lines carry the differential RS-485 signal.
On the microcontroller side, the board provides a D driver data input and an R receiver data output. The DE and NRE lines control the driver and receiver. An onboard 120Ω termination resistor can be enabled using the JP2 jumper when the board is installed at the end of an RS-485 bus.
The module requires a 5V supply, with the manufacturer specifying current consumption from 120µA to 500µA. Board dimensions are 38 × 22mm. The SN65176BDR meets the requirements of ANSI TIA/EIA-422-B and TIA/EIA-485-A and incorporates protection features including current limiting and thermal shutdown.
RS-232 transceiver module based on the MAX232E, designed for bidirectional conversion between TTL/CMOS logic levels and RS-232 signals. It provides two transmit and two receive channels, allowing simultaneous data transmission and reception. The supply voltage range specified in the documentation is 4.5–5.5V. Soldered 333067
UART-RS485 converter module. It enables communication of Arduino boards with industrial modules. DFRobot DFR0259
USB-RS485 converter for industrial applications. It provides communication between the USB interface and the RS485 serial standard. Waveshare USB TO RS485 (B)
No product available!
Converter dedicated to industrial applications. It provides communication between the USB interface and the RS485 serial standard
Converter dedicated to industrial applications. It provides communication between the USB interface and the RS232 and RS485 serial standard
No product available!
Converter dedicated to industrial applications. It provides communication between the USB interface and the RS422 and RS485 serial standard
Converter dedicated to industrial applications. It provides communication between the USB interface and the RS485 serial standard
No product available!
USB-RS485 converter module based on the FTDI FT232RL chip. Provides communication between USB interface and RS485 serial standard
USB-RS485/RS422 converter dedicated to industrial applications. It provides communication between USB interface and RS485 and RS422 serial standard. YN-4852
No product available!
RS485 bus transceiver controlled via USB, equipped with FT230 chip, USB-C connector, ST485BDR controller for 64 devices, galvanic isolation, overvoltage protection and RS485 bus terminator option, ensuring effective and safe communication in industrial systems
USB - RS232/RS485 converter with the original FT2132RNL chip. It uses a USB type A connector and a screw connector to connect RS232 and RS485 interfaces. Supports a wide range of operating systems: Mac, Linux, Android and Windows 11, 10, 8.1, 8, 7. Waveshare USB TO RS232/485
RS422 to TTL converter module based on MAX490 for long-distance bidirectional serial communication, up to 1000 meters, with a transmission speed of up to 2.5 Mbps. Equipped with ESD protection up to 15 kV, TVS diodes and 120 Ω terminating resistors, it provides stability and immunity to interference in demanding industrial conditions. Powered by 5 V, it works with TTL logic and is compatible with popular platforms, and LED indicators facilitate diagnostics and integration.
The board, equipped with the TP8485E transceiver, converts UART signals to RS-485, enabling one-way half-duplex communication at a distance of up to 1200 meters. With its compact design, support for 5V or 12V voltage and compatibility with Seeed Studio XIAO boards, it is ideal for applications in industrial automation, monitoring and data acquisition systems. Seeed Studio 113991354
No product available!
The TTL TO RS485 (C) module enables the conversion of TTL serial signals to differential RS485 while maintaining high noise immunity and galvanic isolation. With its compact design and built-in ESD and surge protection, it is well-suited for automation systems, IoT, industrial applications, and distributed communication—especially in high-interference environments.
No product available!
The TTL-RS485 converter enables easy integration of a microcontroller’s UART port with the RS485 bus, providing half-duplex transmission with automatic direction switching. Thanks to its wide supply voltage range, EMC/EMI resistance, and built-in terminating resistor, it is suitable for industrial communication, automation, and long-distance transmission systems
No product available!
USB to UART (TTL) and RS485 converter, designed for programming and operating FEETECH SMS and SCS series servos. It supports 3.3V and 5V logic levels and a wide range of baud rates from 50 bps to 1 Mbps, providing great application flexibility. The device offers automatic half-duplex switching and overcurrent protection up to 500 mA for increased operational safety. Seeed Studio 100036057
No product available!
Isolated USB-A to RS485 converter based on the FT232RNL chip for bidirectional communication with industrial devices. Supports data rates from 300 to 512000bps, automatic transmission direction control, and RS485 communication over distances up to approximately 1.2km at low baud rates. Features A+, B-, GND screw terminals, TVS and ESD protection, and PWR, TXD, RXD status LEDs. Includes a 1.2m USB-A extension cable and screwdriver. Waveshare USB TO RS485 (C)
No product available!
RS-485 transceiver module based on the SN65176BDR, designed for bidirectional data transmission between a microcontroller and an RS-485 bus. It supports data rates up to 20Mbps and communication distances up to 1200m, while the onboard 120Ω termination resistor can be enabled using the JP2 jumper. Supply voltage is 5V. Soldered 333068