![Main view Main view](https://kamami.pl/73299-large_default/hantek-cc-650-acdc-current-probe-for-oscilloscopes.jpg)
![Main view Main view](https://kamami.pl/73299-large_default/hantek-cc-650-acdc-current-probe-for-oscilloscopes.jpg)
zł406.50 tax excl.
A probe for measuring AC and DC currents up to 650 A. It operates in a bandwidth of up to 400 Hz and can be connected to an oscilloscope via a BNC connector. Hantek CC-650
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
A probe for measuring DC and AC currents up to 650 A. It uses a standard BNC interface and can be connected to an oscilloscope or multimeter. It operates in the frequency band up to 400 Hz. The jaw spacing allows measurement of current flowing in wires with a maximum diameter of 30 mm. It will find use in industry, automotive electronics, power supplies and inverters.
A multifunctional device (computer attachment) that combines a 2-channel digital oscilloscope and a 16-channel logic analyzer. Hantek6022BL
Digital oscilloscope. It has two measurement channels with 100 MHz bandwidth. Hantek DSO2C10
Digital oscilloscope. It has two measurement channels with 150 MHz bandwidth. Hantek DSO2C15
Digital oscilloscope with built-in signal generator. It has two measurement channels with 100 MHz bandwidth and a single-channel signal generator with waveform frequencies up to 25 MHz. Hantek DSO2D10
A universal oscilloscope probe with a BNC connector and a 10:1 voltage divider. It has a frequency response of 200 MHz and allows measurements with a maximum voltage of up to 600 V. Hantek PP-200
6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-1.0mm
No product available!
Micsig MDP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 200 MHz and the ability to measure voltage up to 1500 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig MDP1502
Test probe tip with 500X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 100 MHz and 200 MHz frequency bands. Micsig OP500-2
No product available!
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 350 MHz, it can be connected to the oscilloscope via the BNC connector. Comes with a 10X attenuation tip. Micsig MOIP03P
No product available!
Oscilloscope probe designed for the analysis of signals generated by the ignition coil in automotive engines. It is compatible with most digital oscilloscopes. Hantek HT25
Test probe tip with 2000X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP2000-1G
No product available!
A 20:1 signal attenuator designed to assist in measuring automotive performance, including measuring fuel injector and primary ignition runs. Hantek HT201
No product available!
Test probe tip with 20X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP20-1G
No product available!
Test probe tip with 1000X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 100 MHz and 200 MHz frequency bands. Micsig OP1000-2
No product available!
High voltage differential probe. It has good measurement parameters: 100 MHz band and operating voltage up to 1300 V. The probe has two damping factors: 50X and 500X. Micsig DP10013
Micsig MDP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 100 MHz and the ability to measure voltage up to 700 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig MDP700
High-voltage differential probe. It has good measurement characteristics: a bandwidth of 100 MHz and an operating voltage of up to 1300 V. The probe has two attenuation coefficients: 50X and 500X. Hantek HT8100
Probe for measuring direct current up to 800 A and alternating current up to 500 A. Operates at 5 kHz and can be connected to an oscilloscope via a BNC connector. Powered via USB. Hantek CC-800
Micsig MDP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 150 MHz and the ability to measure voltage up to 1500 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig MDP1501
Cable (adapter) of a BNC connector to banana plugs. Allows convenient connection of a device to an oscilloscope, for example. BNC Q9
A probe for measuring AC and DC currents up to 650 A. It operates in a bandwidth of up to 400 Hz and can be connected to an oscilloscope via a BNC connector. Hantek CC-650