P4100 - universal 100:1 oscilloscope probe
ID: 588154
5906623434480
zł71.44
Tax included
zł58.08 tax excl.
Universal oscilloscope probe with BNC plug with 100: 1 voltage divider and 100 MHz bandwidth. It allows you to perform measurements with a maximum voltage of 2 kV
Description
Universal oscilloscope probe with BNC plug with 100: 1 voltage divider and 100 MHz bandwidth. It allows you to perform measurements with a maximum voltage of 2 kV. The probe ends with a sharp tip, on which you can put an overlay with a hook, and the ground cable has a crocodile clip. It can work with analog and digital oscilloscopes with a standard BNC connector.
Features
- Bandwidth: 100 MHz
- Maximum voltage: 2 kV
- Rise time: 3.5 ns
- Divisor: 100: 1
- Input impedance: 100x: 100 MΩ ± 2%
- Input capacitance 5 pF
- Compensation range: 10 pF - 35 pF
- Cable length: 110 cm
Kit contains
- Oscilloscope probe with BNC connector
- Attachment with a hook
- Set of colored rings
588154
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Single-channel 25 MHz oscilloscope with multimeter function. It allows you to measure direct and alternating voltage, direct and alternating current, resistance, capacity. Equipped with a USB interface. Uni-T UT1025CL
zł1,313.64
Delivery date unknown
No product available!
A multifunctional device (computer attachment) that combines a 2-channel digital oscilloscope and a 16-channel logic analyzer. Hantek6022BL
zł383.75
24h
Available quantity: 6
Available
Other products in the same category (16)
A probe tip with attenuation factor of 10000X. Dedicated to Micsig probes from the SigOFIT series operating in the 500 MHz frequency band. Micsig OP10000-5
zł4,574.96
4 weeks
No product available!
Universal oscilloscope probe with BNC plug and 10:1 voltage divider. It has a frequency range of 60 MHz and allows you to perform measurements with a maximum voltage of up to 600 V.
zł47.75
24h
Available quantity: 4
Available
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 500 MHz, it can be connected to the oscilloscope via the BNC connector. Comes with a 10X attenuation tip. Micsig MOIP500P
zł74,999.00
4 weeks
No product available!
6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-1.5mm
zł47.90
24h
Available quantity: 4
Available
Protective handbag designed for Micsig oscilloscopes of the TO, ATO and STO series.
zł159.86
24h
Available quantity: 2
Available
A probe with a Rogowski coil dedicated to measuring current in a wide frequency range. Measurements can be made without modifying the circuit under test. Micsig RCP500
zł999.01
4 weeks
No product available!
Probe for measuring direct and alternating current up to 100 A. It works in the 800 kHz band, it can be connected to the oscilloscope through the BNC connector. Powered by USB. Micsig CP2100A
zł1,461.29
4 weeks
No product available!
A 20:1 signal attenuator designed to assist in measuring automotive performance, including measuring fuel injector and primary ignition runs. Hantek HT201
zł51.99
24h
Available quantity: 3
Available
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 1 GHz, it can be connected to the oscilloscope via the BNC connector. Comes with a 10X attenuation tip. Micsig MOIP1000P
zł112,990.00
4 weeks
No product available!
Micsig DP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 100 MHz and the ability to measure voltage up to 3000 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP3000
zł1,252.13
4 weeks
No product available!
High-voltage differential probe. It has good measurement characteristics: a bandwidth of 50 MHz and an operating voltage of up to 1300 V. The probe has two attenuation coefficients: 50X and 500X. Hantek HT8050
zł938.99
4 weeks
No product available!
Probe for measuring AC currents up to 1000 A. It works in the range from 10 Hz to 100 kHz, it can be connected to the oscilloscope through the BNC connector. Micsig ACP1000
zł1,199.03
24h
Available quantity: 1
Available
An oscilloscope probe designed to analyze signals generated by the ignition coil in car engines. It is compatible with most digital oscilloscopes. Micsig MS-A-008
zł142.45
24h
Available quantity: 1
Available
The Micsig DP series differential probe is based on advanced metal shielding technology. It offers a 100 MHz frequency bandwidth and the ability to measure voltages up to 7000 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP7000
zł4,199.00
4 weeks
No product available!
A universal oscilloscope probe with a BNC connector and a 10:1 voltage divider. It has a frequency response of 100 MHz and allows measurements with a maximum voltage of up to 600 V. Hantek PP-150
zł28.11
24h
Available quantity: 18
Available
A probe tip with attenuation factor of 2000X. Dedicated to Micsig probes from the SigOFIT series operating in the frequency band of 100MHz, 200MHz and 350MHz. Micsig OP2000-3
zł2,491.68
4 weeks
No product available!
Universal oscilloscope probe with BNC plug with 100: 1 voltage divider and 100 MHz bandwidth. It allows you to perform measurements with a maximum voltage of 2 kV