WEP 995D 2in1 soldering station - hot air and 75W soldering tip
search
  • WEP 995D 2in1 soldering station - hot air and 75W soldering tip
ID: 578805
zł573.76
Tax included

zł466.47 tax excl.

The WEP 995D soldering station is a station consisting of a hot air soldering iron and a tip soldering iron (75 W). It has a PID controller, LCD display, adjustable temperature and air blow out provided by the fan located in the flask. It is used for soldering and desoldering electronic components such as: SOIC, CHIP, QFP, PLCC, BGA, SMD. WEP 995D

1 weeks
On request

Description

The WEP 995D soldering station is a hot air soldering station and tip soldering iron. It is equipped with a microprocessor with a PID controller that checks the operating parameters of the station and corrects them to the set values.

Hot air operation can take place in automatic / manual mode. Choosing the automatic mode, after putting the hot air flask on the stand, the device automatically stops heating and will cool down to a safe temperature. This allows for long, trouble-free operation of the heating element, saving electricity and service security. We choose the manual mode, when we often have to solder something, then we save time and increase work efficiency. It is recommended to switch to automatic mode before finishing work.

The station is equipped with a temperature correction function. It depends on the operating environment, heating element efficiency, blowing power, tip wear, it all affects the correct temperature correction to get the set parameter.

The soldering iron is equipped with a sleep mode, when the tip is not used, after a pre-set time from 0-99 min it goes into sleep mode, i.e. the tip is heated to 200 ° C, which prevents excessive oxidation of the tip, which affects its service life and heating element. We can turn off the mode by setting 0.

Features

  • Voltage: 220 - 240 V
  • Power consumption: 700 W
  • Compact design with a clear LCD display.
  • PID controller
  • Microprocessor control of parameters: temperature, blowing power, working time
  • F/C temperature display mode
  • Hot air station:
    • Airflow: Fan
    • Airflow: up to 120 L/min
    • Smooth temperature control throughout the range
    • Temperature range: 100 - 480°C
    • Temperature stability: ±1°C
    • Display type: LCD
    • The length of the cord in the flask: up to 100 cm
    • Manual/automatic operation mode
    • Protection against reaching too high temperature and informing by the alarm
    • Displays the actual blowing power
  • Arrowhead station:
    • Temperature range: 200 - 480°C
    • Temperature stability: ±1°C
    • Display type: LCD
    • Earth resistance below: 2 ohm
    • Potential to the ground below: 2 mV
    • System: ESD safe
    • Stock tube length: up to 100 cm
    • Sleep mode: activated after idle operation: 0-99 minutes
    • The heating element 50 W, peak power when warming up 75 W, the peak can be up to 140 W
    • 75 W peak power consumption

Included:

  • WEP 995D soldering station
  • A stand for the hotair flask
  • A set of nozzles:
    • Round nozzle with a diameter of 4.4 mm 1130
    • Round nozzle with a diameter of 8 mm 1195
    • Round nozzle with a diameter of 9 mm 1197
    • Square 12 x 12 mm 1313
  • Stand for the tip with cleaning sponge
  • Arrowhead with a T-I tip
  • Gripper for lifting systems
  • Power cord
578805

Data sheet

Station type
2in1 (tip soldering iron + hotair)
Tip soldering iron temperature
200 - 480 °C
HotAir temperature
100 - 480 °C
Power
75 W

Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20

Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20

You might also like

Other products in the same category (16)