Category: RETIRED PRODUCTS

Thermistor for THT assembly with a resistance of 10k, a temperature coefficient of 3380K and accuracy of 1%. The sensor body is Ø2.5x4mm

The Leonardo ETH is a microcontroller board based on the ATmega32U4 and the new W5500 TCP/IP Embedded Ethernet Controller (datasheet).

The DE0-Nano-SoC Development Kit presents a robust hardware design platform built around the Altera System-on-Chip (SoC) FPGA, which combines the latest dual-core Cortex-A9 embedded cores with industry-leading programmable logic for ultimate design flexibility

Ribbon Cable, IDC Socket, IDC Socket, 40 Ways, 5.91 ", 150 mm, 2.54 mm

SMD connector contact UPPER (TOP) 40pin raster 0.5mm

Marcin Bis

A small Li-Pol battery with a nominal voltage of 3.7 V and a capacity of 1350 mAh. Leaded wires, dimensions: 5 x 37 x 59 mm. Akyga LP503759

KAmduino UNO is a development board with functionality and dimensions typical for Arduino UNO. Thanks to the built-in ATmega328P microcontroller and the FT231X chipset, the board can be programmed via a USB interface using the Arduino environment. KAmduino UNO

FPC tape length 250 mm, 50 lines, pitch 0.5 mm. Adafruit 1682

K64 microcontroller with ARM® Cortex®-M4 core, 1MB Flash memory, 256kB RAM, 120MHz, SPI, I2C, I2S, UART, CAN, USB OTG, ADC, DAC, RTC, DMA, LQFP100

SmartLED Shield driver (V4) for SmartMatrix series displays, for use with Teensy 3.2, Teensy 3.5 and Teensy 3.6. It is also possible to connect LED Dotstar or APA102 displays. Adafruit 1902

Add motion, direction and orientation sensing to your wearable FLORA project with this high precision 9-DOF sensors: 3-axis accelerometer, 3-axis magnetometer and 3-axis gyroscope. Adafruit 2020

Ambient Light Sensor, SI1145, connects to the I2C bus pads. Adafruit 1981

Extension for Raspberry Pi; communication module with RS-485 interface (DEV-13000). Module with the possibility of mounting the DB-9 socket, the socket should be purchased separately

FreeSoC2 board has two processors on-board: a CY8C5868LTI-LP039 and a CY8C5888AXI-LP096. The former serves as a debugger/programmer for the latter, which is the target upon which your application code will be installed. Both parts contain a Cortex-M3 processor core, 256kB of flash memory, 64kB of SRAM, and 2kB of EEPROM. DEV-13229

32-bit microcontroller with ARM Cortex-M4 core, XMC4200 family, 256kB Flash, VQFN-48, Infineon

μHex is the first low-power controller which is compatible with Arduino. It is very suitable for the battery power supply environment. A 210mAh CR2032 cell battery could make it work 60 days long. DFR0343

T-Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). Goldpin connectors are included, for self-assembly. Adafruit 1989

Aluminum extensometer beam, allowing weight measurement up to 3 kilograms. It has four wires. It is used in kitchen scales and portable scales.

The I2C electric level conversion module is specifically designed for Banana Pi. The module converts the 3.3V of I2C electric level to 5V level or converts 5V to 3.3V