Category: STARTER KITS, PROGRAMMERS, MODULES

Module with a digital temperature and humidity sensor based on the SHT31-F system. Communication via the I2C interface. Equipped with a Gravity DFRobot SEN0334 connector

The set consists of the STM32 NUCLEO-F401RE board with the STM32F401RE microcontroller and the X-NUCLEO-6180A1 board with the VL6180 distance sensors operating in ToF technology. STMicroelectronics P-NUCLEO-6180A1

Module with PIR EKMB1107112 motion sensor, power consumption in standby mode up to 1 uA. The board communicates via I2C and is equipped with a Qwiic connector. SparkFun SEN-17375

GPS module with NEO-M9N 92-channel GNSS receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. SparkFun GPS-15733

The board is equipped with the STM32F405 microcontroller with the ARM Cortex-M4 core and SPI Flash memory, 20 GPIO pins, SD card slot, pins for connecting the battery with the charging and voltage stabilization circuit, JTAG connector and Qwiic socket. SparkFun DEV-17712

MicroMod main module with STM32 microcontroller. Equipped with an M.2 connector, it can work with MicroMod expansion boards. SparkFun DEV-17713

Module with 6-axis IMU LSM6DSO sensor, which combines a 3-axis accelerometer and gyroscope, as well as a 9kB FIFO buffer and event handling functions. Communicates via I2C or SPI. SparkFun SEN-18020

Module with an EMG signal detector. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020058

Module with a digital temperature and humidity sensor based on the SHTC3 system. Communication takes place via the I2C interface. SparkFun SEN-16467

Set of "sleeping lion" with the educational module micro: bit. It consists of a main plate, noise: bit and felt elements, thread and needle to create the toy. Pimoroni PIM363

ESP32-S3-Touch-LCD-4B is a ready-to-install development board with ESP32-S3 and a 4" touch screen, intended for use in building automation, HMI systems and voice interfaces. The compact 86×86 mm format facilitates integration in wall enclosures and control panels.

DFRobot (DFR0221)

The MicroMod main module with the STM32WB5MMG microcontroller, which allows communication under the Bluetooth Low Energy 5.3, Zigbee and OpenThread protocols. It is equipped with an M.2 connector and can work with MicroMod expansion boards. SparkFun DEV-21438

GPS module with SAM-M10Q GNSS receiver. The chip can receive data from all major positioning systems: GPS, GLONASS, Galileo, QZSS and BeiDou. It has derived UART and I2C interfaces. SparkFun GPS-21834

The module with six touch buttons and LED diodes is designed for micro:bit. It uses the CAP1166 driver and communicates via the I2C interface. Pimoroni PIM401

Audio module with loudspeaker designed to work with micro:bit. There is an amplifier and an 8 Ω 2 W speaker on the board. Pimoroni PIM356

Module with 17x7 LED matrix display (119 LEDs) designed to work with micro:bit. It uses the IS31FL3731 driver and communicates via the I2C interface. Pimoroni PIM353

Module with an analog TEMT6000 light intensity sensor. The voltage at the output is linearly correlated with the intensity of the incident light. The module is supplied with the voltage from 3.3 to 5V. DFRobot SEN0043

Development kit from the M5Stack series equipped with the ESP32-S3 module. It will work well in projects related to IoT or in "wearable" devices. M5 Stack C124

RS485 converter designed for sets from the M5ATOM series. It allows you to connect to development kits devices controlled by the RS485 bus. M5Stack T002