Category: STARTER KITS, PROGRAMMERS, MODULES

Ammeter module designed for M5Stack sets. It can measure direct current in the range from 0 to 4 A with a resolution of approx. 0.15 mA. M5Stack U086

A set for building a walking robot. The chassis is equipped with four servos, a controller and an STM32F030 microcontroller. M5Stack U086

Extension board designed for MicroMod processor modules. All the pins are led out to connectors with a pitch of 2.54 mm. SparkFun DEV-16885

MicroMod main module equipped with Bluetooth 5.0 Sparkfun Artemis. Equipped with an M.2 connector, it can work with MicroMod expansion boards. SprakFun DEV-16401

Doppler radar module with 24GHz BGT24LTR11 transceiver. The board is equipped with a Grove connector and communicates via the UART interface. Seeed Studio 109020021

MicroMod main module with ESP32 chip. Equipped with an M.2 connector, it can work with MicroMod expansion boards. SprakFun WRL-16781

MicroMod main module with SAMD51 microcontroller. Equipped with an M.2 connector, it can work with MicroMod expansion boards. SprakFun DEV-16791

Module with the 3-axis ADXL313 accelerometer with measuring ranges of ± 0.5 g, ± 1 g, ± 2 g or ± 4 g. The system is characterized by high 13-bit resolution and low power consumption. SparkFun SEN-17241

WRL-11395

Development board with Bluetooth 5.2 BGM220P module from Silicon Labs. It is equipped with a mikroBUS socket and a Qwiic connector and a 20-pin connector with peripherals such as I2C, SPI, UART and GPIO. SparkFun DEV-17588

NUCLEO series starter kit equipped with a STM32WL55JC microcontroller (256 KB Flash, Cortex-M4/M0+), with a built-in STLINK-V3E programmer-debugger, equipped with Arduino-compatible connectors

The set consists of the STM32 NUCLEO-F401RE board with the STM32F401RE microcontroller and the X-NUCLEO-53L3A2 board with the VL53L3CX distance sensors operating in ToF technology. STMicroelectronics P-NUCLEO-53L3A2

The module for the RFID reader (125 kHz) is equipped with a USB interface. Works with ID-3LA, ID-12LA and ID-20LA series systems. The selected RFID reader is simply plugged into the module\'s connectors. SparkFun SEN-09963

compact development board with MCX-N947 Dual Arm Cortex M33 microcontroller. It offers a range of advanced features such as Neural Processing Unit, PowerQuad, Smart DMA, Micro SD card slot, Ethernet PHY and HS USB Type-C connectors. NXP FRDM-MCXN947

Module with a MLX90641 thermal imaging camera with a 16x12 field matrix and a 110° viewing angle. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020892

The Fio v3 is a new spin on the Arduino Fio hardware powered by the ATmega32U4. Not only is it small and LiPo-ready, it’s a very capable XBee-ready development board. DEV-11520

Module with 4-channel ADC ADS1015 converter. The system enables analog voltage conversion for both single signals (11-bit resolution) and differential signals (12-bit resolution). I2C communication. SparkFun DEV-15334

Module with an analog MQ6 propane sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0131

GPS module with 72-channel GNSS SAM-M8Q receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART and I2C interfaces. SparkFun GPS-15210

Segger Arduino MKR adapter (8.06.37) with 6-pin 0.05" and 20-pin JTAG connectors, designed for connecting Segger programmers and debuggers, enables efficient programming and testing of Arduino MKR boards.