Module with a deflection sensor with two measuring probes. The board houses the ADS1015 converter, which is an ADC converter with an output in the form of an I2C interface. SparkFun SEN-14666

DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3143

The X-NUCLEO-IHM16M1 motor driver expansion board is based on the STSPIN830 monolithic driver for three-phase brushless motors. It represents an affordable, easy-to-use solution for driving brushless motors in your STM32 Nucleo project, implementing single and three-shunt current sensing

Adapter dedicated to the FLIR Lepton thermal imaging camera. It has been pre-configured to act as a plug-and-play USB camera UVC 1.0, it can also communicate via UART and I2C interface. SparkFun DEV-14670

Module with MLX90614-DCI sensor for non-contact temperature measurement in the range from -70℃ to 270℃. I2C communication. DFRobot SEN0263

Pmod I2S2 is a module with 24-bit A / C and D / C audio converters derived from standard 3,5 mm Jack connectors. Thanks to them, it is possible to send and receive stereo audio signals using the I2S protocol. Digilent 410-379

EEPROM memory in SOIC-8 package. The chip has 32 kb memory (4k x 8 bits). Communication takes place via the I2C interface. ON Semiconductor CAT24C32WI-GT3

VL53L0X ToF Laser Range Finder is a laser distance sensor using the ToF (Time of Flight) measurement technique. The module is supplied with 3.3 ... 5 V voltage and can measure up to 2 m. DFRobot SEN0245

Micro:Mate is an expansion board for the micro: bit development module. It provides six 3-pin connectors with I/O outputs, a 3.5mm audio jack connector and is powered from a 5V microUSB connector. DFRobot DFR0518

ArduCam CSI to HDMI modules are designed to work with cameras: Raspberry Pi V1 and Raspberry Camera V2. ArduCAM CSI to HDMI allows you to extend the signal from cameras using the HDMI <-> HDMI cable (up to 10 meters). Arducam B0091

Pololu Dual G2 High-Power Motor Driver 18v22 is an extension that allows you to control two DC motors designed for Raspberry Pi. The motors can be powered with 6.5-30V and draw up a maximum current of 22A. Pololu 3754

E-Ink display module (ePaper) with a diagonal of 2.9 "and a resolution of 296 x 128 pixels with a SPI controller.   Waveshare 12956

E-Ink display (ePaper) with a diagonal of 1.54 "and a resolution of 200 x 200 pixels with a SPI controller. Waveshare 1.54inch e-Paper (B)

WIFI-LPT100 Eval Kit module enables UART data transmission via WiFi, ultra low power consumption, encrypted communication

E-Ink display (ePaper) with a diagonal of 2.9 "and a resolution of 296 x 128 pixels with a SPI controller. Waveshare 2.9inch e-Paper (B)

Waveshare Photo Interrupter Sensor is an IR optical sensor module with Schmitt trigger and a signaling diode allowing the construction of an incremental encoder. Waveshare Photo Interrupter Sensor

MIC5504-3.3YM5, Single Output LDO 3,3V 300mA, SOT23-5

The S9V11F3S5CMA switching step-up/step-down regulator efficiently produces a fixed 3.3 V (default) or 5 V (selectable) output whether it is higher or lower than the input voltage, which can range from 2 V to 16 V. (Note: minimum start-up voltage is 3 V, but it operates to 2 V after that.)

Pololu Dual G2 High-Power Motor Driver 24v18 is an extension that allows you to control two DC motors designed for Raspberry Pi. The motors can be supplied with 6.5-36V voltage and can draw a maximum current of 18A. Pololu 3756

HDMI 3.5 "480 x 320 pixel color LCD module with touch panel for Raspberry Pi. Waveshare 3.5inch HDMI LCD