Category: Converters USB - UART / RS232
There are 93 products.
Cable with USB-UART converter dedicated to TFmini and TFmini Plus distance sensors. Ended with a USB type A plug and goldpin connectors. Benewake USB-Dupon
The module with the converter USB-UART CP2104 dedicated for minicomputers Raspberry Pi. Adafruit 3589
USB - UART converter based on the CH9102F chip. Compatible with the voltage of 3.3 V and 5 V, it has been equipped with a USB type C connector. Adafruit 5568
USB - RS232 adapter equipped with a USB type A connector and an RS232 connector in the DB9 male standard. It uses the original FTDI FT232RL chip, which guarantees a reliable connection between a variety of devices. Waveshare USB-TO-RS232-Male-Cable
USB - RS485/RS422/RS232 converter designed to convert USB signal to serial signal. It is used to connect devices with USB interface to RS485, RS422 or RS232 network. It uses ADI (Analog Devices iCoupler) galvanic isolation technology. EVC8013B
UART-RS232 converter module. It enables communication of Arduino boards with industrial modules. DFRobot DFR0258
Easy-to-use USB-to-Serial adapter based on the CH340G IC from WCH; works with 5V and 3.3V systems and should auto install on most operating systems without the need for additional drivers; uses the CH340G IC to quickly and easily convert serial signals to USB. DEV-14050
Xbee USB adapter based on the FTDI chip. Intended for configuring Xbee modules. Thanks to the female goldpin connector, it can be used as an FTDI programmer for Arduino FIO / pro / mini / lilypad. DFRobot DFR0050
USB adapter designed for XBee modules. It can be connected to a computer with a USB cable and used with the X-CTU software to configure the XBee. DFRobot DFR0174
The CY7C65213 USB to UART serial breakout is designed to provide users with a means to access all available I/O pins on the IC, and to provide a 6-pin UART header that is compatible with other SparkFun breakout boards. This breakout has a microUSB connector and other support circuitry to get the IC quickly up and running. BOB-13830
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. DEV-09716
USB-UART converter with four isolated UART ports with built-in isolation of 1.5kV/3kV. It guarantees data transmission speeds of up to 12 Mbps and the ability to work with 1.8 V or 3.3 V voltage systems on the UART side. It is equipped with a USB Type C connector and is capable of operating in a wide temperature range from -40°C to +55°C. Electronic Prototypes EPED001A-10-STD
UART converter - USB based on the FT232RL system with TX, RX, RTS and CTS lines led out to the goldpin female connector. It uses a mini USB connector. Adafruit 284
USB - UART converter based on the FT232RL chip. Compatible with voltages of 3.3 V and 5 V, it is equipped with a microUSB connector. Cytron UC00A
RS232 - UART converter based on the MAX3238 chip. It uses all lines of the RS232 interface, thanks to which the user has all the standard\'s functionalities at his disposal. Pololu 126
The converter enables simple connection of the project being built with the UART output to the computer via a USB interface. After connecting to a computer, a virtual COM port is created. MOD-05 / AZ
Uniwersalny konwerter USB z możliwością komunikacji przez najczęściej używane interfejsy UART, I2C, SPI i JTAG. Na płytce znajduje się obwód konwersji poziomów napięcia 3,3V i 5V, co zapewnia lepszą kompatybilność z różnymi urządzeniami. Waveshare USB TO UART/I2C/SPI/JTAG