Category: Sensors

Module with the LIS2DW12 3-axis accelerometer. The system has a user selectable measurement scale of ± 2g/±4g/±8g/±16g. There is a Gravity connector on the board. DFRobot SEN0409

Module with ACHS-7123 current sensor with a measuring range of direct and alternating current from -30 to 30 A. It communicates via an analog interface. Pololu 4032

Module with an incremental encoder with a rotation range of 360°. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020001

Module with a 3-axis MMA7660FC accelerometer with a measuring range up to ± 1.5g. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020039

Module with air quality sensor SGP30. It allows you to read the concentration of VOC (TVOC) and eCO2 and communicates via the I2C interface. Pimoroni PIM480

Module with DHT20 temperature and humidity sensor. It allows you to measure humidity in the range from 0 to 100% and temperature from -40 to 80℃. DFRobot SEN0497

Module with temperature and humidity sensor DHT11. It allows you to measure humidity in the range of 20 ... 90% and temperature (0 ... 50 ° C). DFRobot DFR0067

Module with the MiCS-5524 analog gas sensor. It allows you to measure the concentration of CO, CH4, 2H5OH, C3H8, C4H10, H2, H2S and NH3. DFRobot SEN0440

Range finder with a measuring range up to 12m. The current consumption is up to 120mA and the supply voltage 4.5 ... 6V. Communication via the UART interface. DFRobot SEN0259

Module with a reflection sensor (line sensor) RS-06WD. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020172

I2C BME680 Environmental Sensor is a gas, pressure, temperature and humidity sensor in one MEMS housing. The module is supplied with 3.3-5V, for communication the I2C or SPI interface is used. DFRobot SEN0248

et with a measuring module and a probe for measuring electrical conductivity. It allows you to measure the salinity of water and soil. It has a Gravity analog output interface. DFRobot DFR0300-H

PIR motion sensor module for Arduino and Raspberry Pi. DFRobot SEN0018

The module allows the measurement of lighting in the vicinity of the sensor. The measuring range is from 1 to 65535 LUX, and communication takes place using the I2C bus. DFRobot SEN0097

The module allows the detection of volatile organic compounds (VOC) in the air, based on Winsen\'s WSP2110 system. Allows for detection in the air; formaldehyde (HCHO), methane, benzene, toluene, alcohol, etc. The sensor output is an analog signal. Seeed studio 101020001

Air quality sensor module based on the ENS160 system. It communicates via the I2C or SPI interface. DFRobot SEN0515

Module with a 3-axis MSA311 accelerometer with a configurable measuring range of ±2g/±4g/±8g/±16g. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5309

Module with digital barometer BMP390. It enables pressure measurement from 300 to 1250 hPa and temperature from -40℃ to 85℃. Communicates via I2C or SPI. Adafruit 4816

BME280 integrates onboard temperature sensor, humidity sensor and barometer. It provides both SPI and I2C interfaces; and can be widely used in environmental monitoring, story height measurement and Internet of Things (IoT) control and so on. SEN0236

Module with a digital temperature and humidity sensor based on the SHTC3 system. Communication takes place via the I2C interface. DFRobot SEN0414