Category: Main categories
Subcategories
There are 24191 products.
DFRobot FIT1023 USB camera with an OV5648 sensor and autofocus provides high image quality and easy integration thanks to UVC compatibility. It supports MJPEG and YUY2, operates without drivers, and is used in vision systems, education, automation, and AI prototyping.
Development board based on the R7FA4M1AB3CFM microcontroller and compatible with Arduino UNO R4 Minima. Waveshare R7FA4 PLUS A
A precision reflective sensor utilizing an IR diode and a phototransistor to measure light reflected from a surface. It offers an analog voltage output proportional to the reflected light and an optimal measurement range of 10 mm. Its low power consumption and compact size make it ideal for line-follower robots, edge detection systems, and educational projects. Pololu 4440
Lanberg is a high-quality audio cable with 3.5mm Mini-jack and RCA plugs that provides excellent stereso sound transmission and is compatible with a wide range of devices, chcracterized by resistance to interference and minimal self-noise. Lanberg CA-MJRC-10CC-0015-BK.
A compact relay module with an Omron G5LE-14-DC5 relay, capable of controlling loads up to 10 A with a 5 V coil voltage. Thanks to a BSS138K MOSFET transistor, it can be activated by a 2.5 V to 20 V logic signal, facilitating interoperability with microcontrollers. The module is equipped with 5 mm screw terminals, a 3-pin JST SH connector, and LEDs to indicate operation. Pololu 5662
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
A compact Omron G5LE-14-DC12 relay module that allows you to control loads up to 10 A with a coil voltage of 12 V. Thanks to the BSS138K MOSFET transistor, it can be activated by a 2.5 V to 20 V logic signal, facilitating interoperability with microcontrollers. The module is equipped with 5 mm screw terminals, a 3-pin JST SH connector, and LEDs to indicate operation. Pololu 5663
SMT Breakout PCB for 48-QFN or 48-TQFP - 3 Pack!
The MQ-4 sensor allows methane concentration measurement. The measuring range of the sensor reaches up to 10,000 ppm and an analogue signal is obtained at the output.
The MQ-7 sensor allows you to measure the concentration of carbon monoxide (carbon monoxide). The measuring range of the sensor is in the range of 10 - 10,000 ppm
The MQ-8 sensor allows the measurement of hydrogen concentration in the air. The measuring range of the sensor is in the range of 100 - 10,000 ppm.
Adafruit 1651, 2.8" TFT Touch Shield for Arduino v2
The Lanberg PS0-05E-0100-IEC-BK extension strip with 5 E-type sockets and an IEC C14 connector is an ideal solution for ensuring reliable emergency power supply. Thanks to the possibility of connecting directly to the UPS, the strip provides effective protection for many electronic devices in the event of a power outage. Lanberg PS0-05E-0100-IEC-BK
Set of 100 pieces of shielded RJ-45 category 5E network plugs from Lanberg, designed for LAN FTP cables with a hole diameter of 1.00 ± 0.07 mm, compatible with both wire and stranded, ideal for use with the NT-00204 crimper. Lanberg PLS-5000EZ
Blue LED (460nm) with 1W power equipped with a heat sink. Brightness approx. 30lm, viewing angle 120 degrees.
ARM Cortex-M0 CPU, 32kB Flash, 4kB RAM, 1xUART, 1xI2C, 1xSPI, ADC, LQFP48, STM, RoHS