.png)
12-bit ADS1015 4-Channel ADC I2C with PGA - Soldered
ID: 1208282
zł28.81
Tax included
zł23.42 tax excl.
12-bit ADS1015 analog-to-digital converter module with four single-ended inputs or two differential inputs. It communicates via I2C, supports conversion rates up to 3.3kSPS, and features a programmable gain amplifier (PGA). Designed for analog signal acquisition in microcontroller-based systems. Soldered 333094
Description
The device ADC 12-bit ADS1015 4-channel with PGA breakout by Soldered provides analog-to-digital conversion with a resolution of 12 bits. The onboard ADS1015 offers four inputs operating in single-ended configuration or two differential channels. The module can be used to extend the analog measurement capabilities of development boards and microcontrollers, including data acquisition systems and circuits using analog sensors.
Communication with a microcontroller is handled via the I2C bus. The module supports four hardware-selectable addresses, allowing multiple converters to operate on the same bus. The default address is 0x48. Two Qwiic connectors, compatible with easyC and STEMMA QT, allow solderless connection to compatible boards and modules.
The built-in programmable gain amplifier (PGA) allows the converter's measurement range to be adjusted to the amplitude of the input signal. The ADS1015 supports programmable conversion rates from 128SPS to 3.3kSPS. The ALERT pin can operate as an interrupt output for the programmable comparator, allowing the microcontroller to respond when a configured threshold is exceeded without continuously polling the converter.
The board operates from a 3.3V supply and measures 22 × 22mm. The manufacturer specifies a current consumption of approximately 150µA in continuous-conversion mode at the maximum 3.3kSPS data rate. Two 3.2mm mounting holes are designed for M3 screws.
Features
- ADC and measurement
- IC: ADS1015
- Type: analog-to-digital converter (ADC)
- Resolution: 12-bit
- Number of inputs: 4 single-ended or 2 differential
- Programmable conversion rate: 128SPS–3.3kSPS
- Built-in programmable gain amplifier PGA
- ALERT output for the programmable comparator
- Communication and connectors
- Interface: I2C
- Default I2C address: 0x48
- Four hardware-selectable I2C addresses
- Connectors: 2 × Qwiic, compatible with easyC and STEMMA QT
- Analog inputs: A0, A1, A2, A3
- Power supply
- Board supply voltage: 3.3V
- Current consumption in continuous-conversion mode: approximately 150µA at 3.3kSPS
- Mechanical parameters
- Board dimensions: 22 × 22mm
- Header pin hole diameter: 1.5mm
- Mounting hole diameter: 3.2mm
- Mounting holes designed for M3 screws
1208282
Other products in the same category (16)
Gravity module designed based on the GP8413 system. It is a two-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with a resolution of 15-bit and an accuracy of 0.2%. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1073
zł58.30
24h
Available quantity: 1
Available
Gravity module designed based on the GP8512 system. It is a single-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with a resolution of 15-bit and an accuracy of 0.01%. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1035
zł42.61
24h
Available quantity: 2
Available
Gravity module designed based on the GP8101S system. It is a single-channel DAC (analog-to-digital) converter with PWM communication that offers an output signal with 8-bit resolution and 0.2% accuracy. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1036
zł39.02
24h
Available quantity: 11
Available
Gravity module designed based on the GP8503 system. It is a two-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with 12-bit resolution and 0.1% accuracy. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1034
zł47.24
24h
Available quantity: 3
Available
Gravity module designed based on the GP8501 system. It is a two-channel DAC (analog-to-digital) converter with PWM communication that offers an output signal with 8-bit resolution and 0.5% accuracy. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1037
zł42.46
24h
Available quantity: 3
Available
Gravity module designed based on the GP8211 system. It is a single-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with a resolution of 15-bit and an accuracy of 0.01%. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1071
zł43.38
24h
Available quantity: 14
Available
Module with an 8-channel ADC converter with 8-bit resolution. It uses the ADS7830 chip and is equipped with a STEMMA QT connector, thanks to which it communicates via the I2C interface. Adafruit 5836
zł30.58
24h
Available quantity: 10
Available
8-channel module with current analog outputs ranging from 0 to 20 mA. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in a housing that can be mounted on an industrial rail. Waveshare Modbus RTU Analog Output 8CH
zł90.77
24h
Available quantity: 3
Available
Module with 8 voltage analog outputs with a range from 0 to 10 V. It communicates via the RS485 interface and supports communication within the Modbus RTU protocol. The board is enclosed in a housing that can be mounted on an industrial rail. Waveshare Modbus RTU Analog Output 8CH (B)
zł95.77
4 weeks
No product available!
A compact board with eight 12-bit DACs that allow precise voltage control on each output via I2C communication. Compatible with 3.3V or 5V, it offers flexibility with a reference voltage setting and STEMMA QT or Qwiic connectors for easy integration with other I2C devices. Adafruit 6223
zł130.37
24h
Available quantity: 5
Available
High-quality digital-to-analog converter that allows for pure stereo audio playback without the need for I2C configuration or the MCLK pin. It supports I2S signals (BCLK, WSEL, DIN) and audio formats up to 32 bits and 384 kHz, providing an excellent signal-to-noise ratio (110 dB). Audio output is available via a 3.5 mm jack or on-board pads, and the module works best as a line output to amplifiers and audio systems. Adafruit 6251
zł22.47
24h
Available quantity: 5
Available
High-quality digital-to-analog converter that allows for pure stereo audio playback without the need for I2C configuration or the MCLK pin. It supports I2S signals (BCLK, WSEL, DIN) and audio formats up to 32 bits and 384 kHz, providing an excellent signal-to-noise ratio (112 dB). Audio output is available via a 3.5 mm jack or on-board pads, and the module works best as a line output to amplifiers and audio systems. Adafruit 6250
zł26.27
24h
Available quantity: 26
Available
The Adafruit 5974 module with the HX711 converter enables precise reading of signals from strain gauges and load cells based on a Wheatstone bridge, offering 24-bit resolution and selectable gain. With an integrated screw terminal and options for sampling rate and channel configuration, it is used in projects involving force, pressure, or weight measurement in IoT systems, electronic scales, and mechanical testing.
zł60.34
24h
Available quantity: 12
Available
A module with a 24-bit differential ADC NAU7802 optimized for reading strain gauges in a Wheatstone bridge configuration. It offers high precision force or mass measurements. Thanks to the I2C interface, ready-made libraries and screw connectors, it is easy to integrate, especially in mobile and DIY projects. Adafruit 4538
zł30.86
24h
Available quantity: 16
Available
Miniature USB DAC with the PCM2704 chip enables conversion of a digital audio signal to analog with high quality and low distortion. Powered from the USB port, it works with Windows, MacOS and Android OTG systems, offering analog and SPDIF outputs for HIFI and mobile audio applications.
zł28.70
24h
Available quantity: 7
Available
DFRobot DFR1184 module with a 15-bit ADS1115 converter enables precise voltage measurements of 0–10 V from industrial sensors. The dual-channel design, support for I2C/UART, and compatibility with popular platforms make it an effective solution for automation systems, environmental monitoring, and energy management.
zł55.67
4 weeks
No product available!
12-bit ADS1015 analog-to-digital converter module with four single-ended inputs or two differential inputs. It communicates via I2C, supports conversion rates up to 3.3kSPS, and features a programmable gain amplifier (PGA). Designed for analog signal acquisition in microcontroller-based systems. Soldered 333094