TB6612 1.2A DC/Stepper Motor Driver - dual DC motor driver module TB6612FNG
ID: 1182120
5906623469871
zł33.91
Tax included
zł27.57 tax excl.
TB6612FNG dual DC motor controller module. It can be used as a stepper motor driver or solenoid driver. Adafruit 2448
Description
Dual DC motor driver module based on TB6612FNG. The chip has two full H-bridges built-in, which means it can drive 2-4 solenoids (only two can be active at the same time, on opposite bridges), two DC motors or one stepper motor. It allows you to control drives with a voltage range of 4.5 to 13.5 V, and each channel can draw a current of 1.2 A (instantaneous 3 A). The module is controlled with PWM signals for speed control and digital outputs for direction control. It operates with voltages from 2.7 to 5 V. It will work well in small mobile robot projects and for controlling home automation components. Full documentation with examples of use is available on the product page.
Features
- 2 channels for DC motors
- Possibility to control a stepper motor
- Power supply for motors: from 4.5 to 13.5 V
- Output current: 1.2 A (instantaneous 3 A) per channel
- Switching frequency: 100 kHz
- Digital interface (PWM and digital outputs)
- Supply voltage: 2.7 V to 5 V
- Dimensions: 27 x 19 x 3 mm
Kit contains
- TB6612 1.2A DC/Stepper Motor Driver module
- Goldpin male connector
1182120
Data sheet
- Output current
- 1,2 A
- Number of channels
- 2
- Supply voltage min
- 4,5 V
- Supply voltages max
- 13,5 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Bipolar stepper motor. It has a resolution of 200 steps/revolution (1.8 ° per step), has a nominal voltage of 7.4 V, and draws a current of 0.28 A per coil. Pololu 1207
zł163.48
24h
Available quantity: 1
Available
DC motor set with a two-sided shaft and a matching 66mm diameter wheel with the tire. HC02-48
zł5.58
24h
Available quantity: 20
Available
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.35
24h
Available quantity: 367
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.31
24h
Available quantity: 87
Available
Other products in the same category (16)
Dual motor controller allowing two DC motors to be driven with voltages from 4.5 to 13.5V and a continuous current of 1.2 A per channel. SparkFun ROB-14450
zł81.77
24h
Available quantity: 1
Available
DC motor driver that allows you to control the movement of three drives using the I2C interface. Board with soldered connectors. Pololu 5033
zł226.36
24h
Available quantity: 1
Available
The controller enables to supply the motors with voltage in the range of 10-47V and power consumption in continuous operation of 1.7A (4.5A peak) for each channel in dual or 3.4A mode (9A peak) in single channel mode. Pololu 2999
zł56.09
24h
Available quantity: 3
Available
The pad for use with shallow Feather series contains two TB6612 chips that allow you to control DC motors or stepper motors. The I2C interface is used to communicate with the overlay. Adafruit 2927
zł113.25
24h
Available quantity: 3
Available
DC motor driver with a working voltage from 5 to 30 V and a maximum continuous current of 13 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MD10C
zł58.19
24h
Available quantity: 7
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5036
zł352.15
4 weeks
No product available!
This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 Voperating range and are efficient enough to deliver a continuous 18 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation.
zł344.17
24h
Available quantity: 1
Available
Single-channel DC motor controller enabling motor control with voltage in the range of 7-30V and current up to 10A. The set has a potentiometer and a direction switch. Cytron MD10_POT
zł54.49
24h
Available quantity: 45
Available
Module with a DC motor driver based on the MC33886 chip. It allows you to control the movement of drives with a working voltage from 5 to 28 V and a current of up to 5 A
zł41.43
4 weeks
No product available!
An H-bridge capable of controlling one DC motor in both directions or two unidirectional motors at voltages from 4.5 to 44 V and continuous currents up to 1.3 A. The module offers three operating modes (PH/EN, IN/IN, half-bridge), built-in current limiting and measurement, and protection against overheating, overload, undervoltage, and reverse polarity. Its compact design, flexible logic power supply (1.8–5.5 V), and simple control make it ideal for robotics, automation, and hobby projects. Pololu 4971
zł18.84
24h
Available quantity: 2
Available
The UX-52 panel brush motor speed controller is a versatile device with speed adjustment from 90 to 1400 rpm. It offers precise control of motors with an input voltage of 220VAC, featuring a solid construction and a convenient digital display.
zł107.76
4 weeks
No product available!
Motoron M3S256 Triple Motor Controller Shield - 3-channel DC motor driver for Arduino (for assembly)
DC motor driver that allows you to control the movement of three drives using the I2C interface. Plate with connectors for assembly. Pololu 5031
zł202.77
4 weeks
No product available!
A two-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors. Pololu 5080
zł86.42
24h
Available quantity: 2
Available
Shield with dual-channel DC motor driver for Arduino. It has an operating voltage from 7 to 30 V and a continuous current of up to 1.2 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-3AMOTOR
zł111.29
24h
Available quantity: 2
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for assembly. Pololu 5052
zł332.37
4 weeks
No product available!
Module with a 2-channel driver for DC motors TB6612FNG designed to work with the Raspberry Pi. It can work with voltages from 6 to 12 V and currents up to 3 A. SB Components 21468
zł91.17
24h
Available quantity: 2
Available
TB6612FNG dual DC motor controller module. It can be used as a stepper motor driver or solenoid driver. Adafruit 2448