SEGGER (Q)SPI Flash Evaluator Adapter board Pack for BGA (6.40.02)

SiFive-ARTY adapter for debugging between J-Link and the ARTY board with SiFive RISC-V. Segger SiFive-ARTY Adapter (8.06.24)

An adapter that allows the J-Link device to connect to Microchip microprocessors that use an RJ11 debug connector, converting the standard 20-pin .1" connector to a 6-pin RJ11 connector. With this tool, users can take full advantage of 2-wire JTAG debugging capabilities, including process tracing, memory analysis, and real-time device control, and the 21 cm RJ11 cable provides convenience in connecting to the target system. Segger Microchip 2-Wire JTAG TDI Adapter (06/08/23)

The SEGGER USB Hub is a seven-port, industrial-grade USB hub that provides power to Flasher Compact devices and connects them to the Flasher Hub. Segger USB Hub (5/01/10)

A specialized demonstration board designed to support Tail Tagging within the embOS/IP IP stack. Using this technology, it is possible to transform a single Ethernet port into several logical ports, enabling the creation of a virtual multiport network using only a single Ethernet port. Segger embOS/IP Switch Board (6.70.00)

A set of three SON/DFN adapters enables easy testing and programming of flash devices in these packages, eliminating the need for dedicated solutions for each form factor. The adapters are compatible with the SEGGER (Q)SPI Flash Evaluator and other test systems, making them a versatile tool for both test and production. SEGGER (Q)SPI Flash Evaluator Adapter board Pack for SON/DFN (6.40.03)

J-Link 9-pin Cortex-M Adapter, RoHS, Segger

Adapter enabling easy connection of a Microchip AVR microcontroller device with the SEGGER Flasher programming system, supporting 6-pin and 10-pin connectors and providing fast connection via SPI protocol. With the function of powering the target hardware (3.3V or 5V) and direct power supply via VTREF connection, the adapter is flexible, easy to use and ideal for programming and debugging AVR microcontrollers in embedded systems, providing reliable communication and high precision. Segger AVR SPI Adapter (8.06.25)

The Segger J-Link USB Isolator (8.07.02) provides isolation up to 3 kV DC and supports USB Full-Speed transmission with a maximum output current of 200 mA. The device is equipped with short-circuit protection and LED indicators for power status and overload.

Adapter that enables JTAG connection between Flasher programmer and target hardware with Power Architecture or PowerPC microcontrollers. Converts 20-pin 0.1\'\' connector to 14-pin JTAG, ensuring compatibility, stability and secure connection. Segger PPC 14-Pin Adapter (06.08.07)

A device that provides electrical isolation between the J-Trace emulator and the ARM board, which protects against electrical interference, especially in systems where the development tools and the application do not share the same ground. It provides 1 kV DC isolation, supports trace frequencies up to 75 MHz, and is compatible with J-Trace V2 and later versions, with a minimum power consumption of 25 µA. Segger J-Trace Isolator (07/08/10)

AVR PDI adapter from standard 2.54mm 20 pin connector to 2.54mm 6 pin, 1.27mm 6 pin or 2.54mm 10 pin AVR PDI connector. Segger AVR PDI Adapter (8.06.26)

Xilinx adapter that connects to Xilinx\'s 14-pin, 2mm JTAG connector, providing debugging of MCU cores such as the Arm Cortex-A9 on Xilinx Zynq FPGAs. With its compact design and high signal quality, it is a reliable tool for engineers working with FPGA platforms. Segger Xilinx Adapter (06/08/19)

The Intel FPGA Adapter (formerly J-Link Altera Adapter) connects to the Intel FPGA 10-pin JTAG connector, enabling debugging of FPGA-based MCU cores such as the dual-core Arm Cortex-A9 in Cyclone V devices. on Intel FPGA solutions.

Compact development board with NXP LPC54605J512 microcontroller, ideal for prototyping and testing USB solutions, equipped with two USB-Host ports and support for SEGGER software such as emUSB-Host, emLoad and embOS. Thanks to the simple firmware update process and the built-in J-Link OB debugger, the board allows you to quickly and conveniently start working with USB devices in embedded projects. Segger emPower-USB-Host (6.90.00)

A compact reference platform that enables rapid testing and verification of trace configurations, providing excellent signal quality for analysis. With the ST STM32H743 microcontroller and support for JTAG, SWD and SWO debugging interfaces, the board provides high performance and flexibility in monitoring system performance. Segger STM32H7 Trace Reference Board (6.68.20)

The Segger J-Link Microchip Adapter (8/06/09) provides a debug connection between a J-Link probe and hardware with Microchip PIC32 series microcontrollers. Supports RJ12 debug connector, 14-pin MIPS connector and 6-pin PICkit connector.