Segger J-Link Microchip Adapter (8.06.09)

The Segger J-Link USB Isolator (8.07.02) provides isolation up to 3 kV DC and supports USB Full-Speed transmission with a maximum output current of 200 mA. The device is equipped with short-circuit protection and LED indicators for power status and overload.

A set of three BGA adapters enables easy testing and programming of flash devices in these packages, eliminating the need for dedicated solutions for each form factor. The adapters are compatible with the SEGGER (Q)SPI Flash Evaluator and other test systems, making them a versatile tool for both test and production. SEGGER (Q)SPI Flash Evaluator Adapter board Pack for BGA (6.40.02)

SiFive-ARTY adapter for debugging between J-Link and the ARTY board with SiFive RISC-V. Segger SiFive-ARTY Adapter (8.06.24)

Adapter enabling easy connection of a Microchip AVR microcontroller device with the SEGGER Flasher programming system, supporting 6-pin and 10-pin connectors and providing fast connection via SPI protocol. With the function of powering the target hardware (3.3V or 5V) and direct power supply via VTREF connection, the adapter is flexible, easy to use and ideal for programming and debugging AVR microcontrollers in embedded systems, providing reliable communication and high precision. Segger AVR SPI Adapter (8.06.25)

A 1:1 adapter that allows you to connect a standard 20-pin connector to its 2mm pitch counterpart without any additional configuration. For some models, such as the J-Link PRO, pins 14, 16, 18 and 20 may not be connected to ground, so it is recommended to leave them unconnected on the target hardware. Segger 2mm Adapter (06/08/11)

Segger adapter 8.06.28 allows conversion from a 20-pin 0.1" connector to a 10-pin 0.05" Cortex-M type connector with the option of custom pin mapping. A useful solution for integrating programmers and debuggers with devices featuring different pin configurations.

Professional reference board with ARM Cortex-M4F microcontroller, designed for code tracing and real-time application analysis. Equipped with an external 19-pin debug port and test points for trace signals, it enables easy integration with J-Link and J-Trace programmers, supporting Embedded Trace Macrocell (ETM) technology. Segger Cortex-M Trace Reference Board (6.68.18)

The Segger J-Link Signal Smoothing Adapter (8/06/12) is designed to improve signal integrity between the J-Link debug probe and the target debug device. It allows JTAG signals to be suppressed by adjustable series resistors, preventing excessive gain and jitter.

Adapter enabling connection of Flasher PRO programmers and other Flasher models to devices with a 10-pin Renesas connector. It is compatible with M16C, M32C, R8C and R32C microcontrollers, providing stable communication and easy integration with older and modern programming systems. Segger Renesas M16C Family 10-Pin Adapter (8.06.40)

An adapter to connect the JTAG to a target hardware system that has an automotive connector. It has a 20 pin 2.54mm JTAG connector and a 19 pin 1.27mm Samtec FTSH connector. Segger Infineon AUTO-20 Adapter (8.06.33)

RS232 module used as a communication extension equipped with a female DSUB9 connector, allowing easy connection to a PC or USB-RS232 adapter. Segger emPower RS232 Add-On (6.32.32)

The RX FINE adapter converts a standard 20-pin 2.54 mm connector to a 14-pin 2.54 mm connector. It enables the connection of Segger programmers with RX devices from Renesas. Segger RX Fine Adapter (8.06.10)

J-Link 14-pin TI Adapter, RoHS, Segger

Segger Arduino MKR adapter (8.06.37) with 6-pin 0.05" and 20-pin JTAG connectors, designed for connecting Segger programmers and debuggers, enables efficient programming and testing of Arduino MKR boards.

Adapter providing two dedicated supply voltages - for programming and powering for the target board. Useful for programming modules that do not support low voltage programming or require a voltage other than 5V. Segger Programming Voltage Adapter (8.06.30)

A power adapter that provides a stabilized supply voltage to the target board (can be adjusted from 3.6V to 0.8V). Segger Target Supply Adapter (8.06.18)