New products
New products New products
Best sellers
There are 16535 products.
Nylon PA12 filament in Natural with a diameter of 1.75 mm. 0.75 kg of filament is wound on a spool. Fiberlogy Nylon PA12 Natural
ToF distance sensor (Time of flight) with a range of up to 5 m. The module is supplied with the voltage of 3.3 V and communicates via the I2C interface. SparkFun SEN-19037
Module with 9-axis IMU. It combines the ISM330DHCX (accelerometer and gyroscope) and MMC5983MA (magnetometer) systems. Communication via the I2C interface. SparkFun SEN-19895
FiberFlex 40D filament in Purple with a diameter of 1.75 mm. 0.85 kg of filament is wound on a spool. Fiberlogy FiberFlex 30D Purple
The XTAR VC2 charger is a two-channel charger for lithium-ion (Li-ion) cells with a micro USB charging input. Each channel is independent. The VC2 has a large LCD screen showing charging voltage and current. The charger also shows the capacity that is delivered to the cell and displays the result on the screen
A module dedicated to Raspberry Pi power management. It has a built-in RP2040 microcontroller that controls the operation of the device. Waveshare Power Management HAT (B) (EU)
The module with the AR0234 sensor, working with all versions of the Raspberry Pi. The sensor used has a matrix of 2.3 MP and allows you to record video at resolutions 1920x1200 @ 60fps. ArduCAM B0353
The Tic 36v4 USB Multi-Interface High-Power Stepper Motor Controller makes basic control of a stepper motor easy. Pololu 3141
The IO expansion module is designed to work with the micro:bit educational board. There are 20 GPIO pins on the board, a buzzer and a voltage stabilization circuit
Module with an IO pin expander based on the TCA9534 system. It allows you to add 8 GPIO pins to an I2C-controlled project. SparkFun DEV-17047
Universal programmer for serial EEPROM and Flash memories, including AVR, STM32 and STM8 microcontrollers. It is controlled from a computer using a USB interface and software for Windows systems, but it can also operate autonomously without a computer. SkyPRO II
The MPX5700AP air pressure sensor with a measuring range from 15 to 700 kPa. It communicates via the I2C interface. DFRobot SEN0456
Module with 25 QTR type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 50 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4225
Module with ePaper 2.9" display and RP2040 microcontroller. Equipped with QW/ST connector. Accessories included. Pimoroni PIM610
Miniature, 12V brush DC motor with metal gear with 15.25: 1 ratio. It has a cross section of 10 × 12 mm, and the D-shaped output shaft has a length of 9 mm and a diameter of 3 mm. It also has an extended motor shaft with dimensions of 4.5 × 1 mm. Pololu 4789
RC extension cable dedicated to servos, comes with JR/Futaba female and male connectors
RC extension cable dedicated to servos, comes with JR/Futaba female and male connectors
This sensor is a carrier/breakout board for ST’s VL6180X proximity and ambient light sensor, which measures the range to a target object up to 20 cm away (or 60 cm with reduced resolution). Pololu 2489
Power filter board dedicated to Raspberry Pi minicomputers and DAC audio modules. It integrates various types of capacitors and allows you to remove power noise. DFRobot DFR0940.
Probe for measuring AC currents up to 1000 A. It works in the range from 10 Hz to 100 kHz, it can be connected to the oscilloscope through the BNC connector. Micsig ACP1000