- Out-of-Stock
FRDM-KE04Z - starter kit with Freescale Kinetis KE04Z microcontroller (5V power supply)
ID: 233083
Freescale starter kit with Kinetis KE04Z microcontroller (Cortex-M0 +, 5V power supply ), integrated with the OpenSDA debugger-programmer, capacitive switch, LED-RGB and MEMS 3D accelerometer. Arduino-compatible outputs.
FRDM-KE04Z
Freedom development platform based on Kinetis KL04Z MCUs, Freescale, RoHS
The FRDM-KE04Z is an ultra-low-cost development platform for Kinetis KE04 MCUs built on ARM® Cortex®-M0 + processor and with 8 KB Flash. Features include easy access to MCU I / O, battery-ready, and a standard-based form factor with expansion board options and a built-in debug interface for flash programming and run-control. The FRDM-KE04Z is supported by the Freescale and third-party development software.
Features:
- MKE04Z8VFK4 MCU - 48 MHz, 8 KB Flash, 1 KB SRAM, 24 QFN
- Capacitive touch slider, MMA8451Q accelerometer, Tri-color LED
- Flexible power supply options - USB, external source
- Easy access to MCU I / O
- IrDA transmitter and receiver
- Form factor compatible with Arduino ™ R3 pin layout
- New, OpenSDA debug interface
- Mass storage device flash programming interface (default) - no tool installation required to demo apps
- P & E debug interfaces provides debugging and compatibility with IDE tools
- CMSIS-DAP interface: new ARM standard for embedded debug interface
Contents:
- FREEDOM-KE04Z Board
233083
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Cable with USB plugs type A and mini-USB type B, cable with a length of 1.8 m
zł9.02
Delivery date unknown
No product available!
Freescale starter kit with Kinetis KL25Z family microcontroller (Cortex-M0 +), integrated with the programmer-debugger OpenSDA, capacitive switch, LED-RGB and MEMS 3D accelerometer. Arduino-compatible outputs.
zł139.00
24h
Available quantity: 2
Available
Freedom Development Platform for the Kinetis KL05 MCUs, Freescale, RoHS
zł102.90
24h
Available quantity: 2
Available
Easy-to-use retractable cable with USB type A plugs and mini-B type, the cable is 73 cm long after being unrolled
zł8.83
24h
Available quantity: 99
Available
Starter kit with a microcontroller from the Kinetis KL46Z family (Cortex-M0 +), integrated with the OpenSDA programmer-debugger, capacitive touch slider, LED, MEMS 3D accelerometer and 4-digit LCD. NXP FRDM-KL46Z
zł269.84
24h
Available quantity: 4
Available
Plastic housing for FREEDOM sets (Freescale FRDM), Bud Industries
zł62.13
24h
Available quantity: 1
Available
Freescale Freedom Development Platform for Kinetis K64, K63, and K24 MCUs, Freescale, RoHS
zł309.00
Delivery date unknown
No product available!
Other products in the same category (16)
WiFi 802.11 b / g / n module with ESP8266 system, 5 leads are available with 2 mm pitch with the possibility of soldering of gold pins, power lines, reset line and UART interface have been led to the connector. 3.3V power supply
Retired
No product available!
No product available!
No product available!
Wheels fit 2 mm diameter output shafts such as the ones on our sub-micro plastic planetary gearmotors. Pololu - 2356
Retired
No product available!
No product available!
No product available!
A minisumo robot on a tracked chassis with Pololu 100:1 HP motors. Fully assembled robot, additionally requires four AA batteries. Pololu 3127
Retired
No product available!
Arduino Mini is a module designed for use on a contact board. Version 05 has an ATmega328 microcontroller from the AVR family in a smaller enclosure, which allows the placement of all components on one side of the board. The board has a reset button . Version 05 has the same spacing as version 04. A000087
Retired
No product available!
No product available!
No product available!
The Cloudshell for XU4 is an affordable DIY Network Attached Storage (NAS) Solution to create your own personal cloud! It includes a color LCD console display on the front and has room for a 2.5inch HDD/SSD along with the XU4 board inside the CloudShell
Retired
No product available!
No product available!
No product available!
No product available!
Generic Linear Actuator with Feedback: 8" Stroke, 12V, 0.6"/s
Retired
No product available!
Li-Ion battery charger dedicated for Yato 18V systems. It is perfectly matched to batteries with capacities from 2000 mAh to an impressive 6000 mAh, ensuring a full charge in just 1 to 3 hours. Yato YT-82848
Retired
No product available!
Freescale starter kit with Kinetis KE04Z microcontroller (Cortex-M0 +, 5V power supply ), integrated with the OpenSDA debugger-programmer, capacitive switch, LED-RGB and MEMS 3D accelerometer. Arduino-compatible outputs.