

4-digit, 8-segment LED display module with 8-step brightness adjustment. There is a Gravity connector on the board, which allows you to easily connect the module to the control board. Communication with the display takes place via the I2C interface. On the Wiki page there is a user manual and sample programs.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
Board with ATmega1280 microcontroller from the AVR family, the user has 54 I/O lines, 14 PWM channels, 16 analog inputs. DFRobot DFR0003
No product available!
4-digit, 8-segment LED display module with 8-level brightness adjustment. Communication via the I2C interface. DFRobot DFR0645-G
The infrared distance sensor enables the detection of objects in the range from 3 to 50cm. The sensor has a digital output, the detection threshold is adjusted by a potentiometer. DFRobot SEN0164
TCS34725 RGB Color Sensor is a color sensor TCS34725 controlled by the I2C interface. It is powered by voltage in the range of 3.3 ... 5V and is intended for Arduino-compatible boards. DFRobot SEN0212
No product available!
A sensor that detects the concentration of ammonia. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0469
No product available!
Module with 9-axis IMU BMX160 sensor (accelerometer, gyroscope and magnetomet) and BMP388 pressure/temperature sensor. Communication via the I2C interface. DFRobot SEN0252
Module with an analog TEMT6000 light intensity sensor. The voltage at the output is linearly correlated with the intensity of the incident light. The module is supplied with the voltage from 3.3 to 5V. DFRobot SEN0043
The expansion board is designed for DFRduino M0 or Bluno M0 sets. The board has 31 GPIO pins (including 6 PWM and 6 ADC inputs), UART, I2C and SPI interfaces. The pins are color coded according to the Gravity standard. DFRobot DFR0412
A set of 5 modules with a button and LED backlight. The boards are equipped with a Gravity connector and communicate via a digital interface. DFRobot DFR0785
A set with a radio transmitter and receiver operating at 433 MHz. The modules are equipped with Gravity connectors and communicate via a digital interface. DFRobot TEL0140-1
Module with distance sensor Sharp GP2Y0D810Z0F operating in the infrared band. It is powered with a voltage ranging from 2.7 to 6.2 V and has a digital output (Gravity connector). DFRobot SEN0042
NFC module with built-in antenna on the board. The module has a Gravity connector. Memory communication can be done through one of the serial interfaces: UART or I2C. DFRobot DFR0231-H
Set with a measuring module and a probe for measuring the pH of wet soil and food products. The module is powered with the voltage of 5 V and has an analog output with a voltage range from 0 to 4 V. DFRobot SEN0249
No product available!
Digital signal isolator for communication via the Gravity I2C interface. It allows you to isolate the I2C digital signal and provide isolated power to the sensor module. DFRobot DFR0565
No product available!
Sensor that detects the concentration of ozone. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0472
No product available!
Flexible 16x16 RGB LED matrix module. The set uses addressable SK6812/WS2812B diodes. DFRobot DFR0463
No product available!
A sensor that detects the concentration of carbon monoxide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0466
No product available!
Set with the ADC HX711 transducer module and a pressure sensor in the form of a tensometric beam. It communicates via the UART interface. It allows you to build a simple home scale. DFRobot SEN0160
4-digit, 8-segment LED display module with 8-level brightness adjustment. Communication via the I2C interface. DFRobot DFR0645-R