Grove I2C Thermocouple Amplifier
ID: 583179
zł93.81
Tax included
zł76.27 tax excl.
The module with the MCP9600 amplifier is designed to work with a thermocouple. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 101020594
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
The module with the MCP9600 amplifier is designed to work with a thermocouple. There are four pads on the bottom that allow you to read the alarms of exceeding the temperature generated by the amplifier. The board is equipped with a Grove connector, so it can be used with the Base Shield V2 and Arduino extension. The module communicates via the I2C interface and is supplied with the voltage of 3.3 V or 5 V. It will be used in projects requiring measurement in a wide temperature range. Full documentation of the module with examples of use is available on the product page.
Features
- Works with K, J, T, N, S, E, B and R thermocouples
- Measurement accuracy: 1.5°C
- Measurement resolution: 0.0625°C
- Integrated cold junction compensation
- 4 programmable alarm outputs
- Digital filter and programmable hysteresis
- Low power mode
- Interface: I2C
- I2C address: 0x60 (default) or 0x67
- Supply voltage: 3.3 V or 5 V
- Dimensions: 20 x 40 x 18mm
- Weight: 11 g
Kit contains
- Grove I2C Thermocouple Amplifier module
- Grove cable
583179
Data sheet
- Interface
- I2C
- Type of sensor
- inny
- Power supply voltage
- 3,3 - 5 V
- Sensor type
- Wzmacniacz termopary
You might also like
Board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface
zł55.92
24h
Available quantity: 68
Available
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł113.90
24h
Available quantity: 70
Available
With the help of a thermocouple, it is possible to measure the temperature of the air and the surface. The use of a steel stainless steel tip in a K-type thermocouple allows the temperature to be measured up to 500 ° C. The cord length is approximately 100 centimeters. Adafruit 3245
zł56.17
24h
Available quantity: 3
Available
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
zł24.40
24h
Available quantity: 20
Available
Grove module with temperature, humidity and pressure sensor. The board is equipped with a Grove connector and communicates via I2C or SPI. Seeed Studio 101020193
zł92.99
24h
Available quantity: 4
Available
Other products in the same category (16)
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 103020024
zł154.13
24h
Available quantity: 2
Available
Module with a SI1145 light sensor that can detect waves with a wide range of wavelengths: UV, visible and infrared light. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020089
zł58.33
24h
Available quantity: 3
Available
Module with a button and RGB LED backlight. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020049
zł20.91
6 weeks
No product available!
The kit includes a control module (with ETA1617 and NE555) and an ultrasonic transducer. The water atomiser module allows for the construction of, for example, a small humidifier. The module has a connector in accordance with the Grove standard. Seeed studio 101020090
zł64.50
24h
Available quantity: 3
Available
Module for recording sounds, which can store recordings up to 20 seconds. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 107020007
zł39.30
24h
Available quantity: 3
Available
Module with 8x8 LED matrix in red and HT16K33 LED driver. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 104020089
zł69.62
6 weeks
No product available!
Module with a driver designed for small DC motors. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020084
zł7.49
6 weeks
No product available!
A set of necessary tools needed to perform vehicle diagnostics. It consists of a CAN Bus module, an OBD II connector and the necessary wires. Seeed Studio 114991438
zł116.83
6 weeks
No product available!
The expansion module is designed for Raspberry Pi minicomputers. It is equipped with connectors to which you can attach modules compatible with the Grove standard. Seeed Studio 103030275
zł49.48
24h
Available quantity: 1
Available
Module with a gas concentration sensor MQ9, which enables the detection of carbon monoxide and combustible gases (methane, propane). The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020045
zł57.71
24h
Available quantity: 1
Available
Module with GP2Y0D805Z0F proximity sensor, which can detect the presence of objects in the range from 0.5 to 5 cm. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020578
zł41.96
24h
Available quantity: 2
Available
Module with OTP-538U non-contact temperature sensor. The board is equipped with a Grove connector and has analog outputs. Seeed Studio 101020062
zł63.41
24h
Available quantity: 3
Available
Kit with MPX5700AP pressure sensor, syringe and tube. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 110020248
zł199.74
6 weeks
No product available!
Module with a dynamic NFC M24LR64E-R tag and an external antenna. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020070
zł129.00
6 weeks
No product available!
Module with a button and red LED backlight. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020044
zł13.68
24h
Available quantity: 2
Available
The module with the ACS70331 current sensor with a direct current measuring range up to 2,5 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020652
zł48.34
24h
Available quantity: 3
Available
The module with the MCP9600 amplifier is designed to work with a thermocouple. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 101020594