![P6100 - A pair of 10:1 universal oscilloscope probes](https://kamami.pl/76762-large_default/p6100-universal-101-oscilloscope-probe.jpg)
![P6100 - A pair of 10:1 universal oscilloscope probes](https://kamami.pl/76762-large_default/p6100-universal-101-oscilloscope-probe.jpg)
zł45.45 tax excl.
Universal oscilloscope probe with BNC connector. It has a voltage divider of 10:1 and offers a frequency response of 100 MHz. It allows measurements with a maximum voltage of up to 600 V. P6100
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
Universal oscilloscope probe with BNC connector. It has a voltage divider of 10:1 and offers a frequency response of 100 MHz. It allows measurements with a maximum voltage of up to 600 V. The probe is terminated with a sharp tip on which a cap with a hook can be applied, while the ground lead has a crocodile connector. It can be used with analogue and digital oscilloscopes with a standard BNC connector.
Digital oscilloscope. It has two measurement channels with 100 MHz bandwidth. Hantek DSO2C10
Oscilloscope probe with BNC plug with 100MHz bandwidth. Uni-T UT-P04
Protective handbag designed for Micsig oscilloscopes of the TO, ATO and STO series.
A set of needle probes used for piercing wire insulation. They can be used as pin probes when working with small PCBs or connectors. Hantek HT307
A probe for measuring AC and DC currents up to 650 A. It operates in a bandwidth of up to 400 Hz and can be connected to an oscilloscope via a BNC connector. Hantek CC-650
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 1 GHz, it can be connected to the oscilloscope via the BNC connector. Comes with a 10X attenuation tip. Micsig MOIP10P
No product available!
Micsig MDP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 100 MHz and the ability to measure voltage up to 1500 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig MDP1501
Oscilloscope Probes (pair). 460-004
Oscilloscope probe designed for the analysis of signals generated by the ignition coil in automotive engines. It is compatible with most digital oscilloscopes. Hantek HT25
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 350 MHz, it can be connected to the oscilloscope via the BNC connector. Comes with a 10X attenuation tip. Micsig MOIP03P
No product available!
6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-2.3mm
Test probe tip with 1000X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP1000-1G
No product available!
Probe for measuring direct and alternating current up to 100 A. It works in the 2,5 MHz band, it can be connected to the oscilloscope through the BNC connector. Powered by USB. Micsig CP2100B
A 20:1 signal attenuator designed to assist in measuring automotive performance, including measuring fuel injector and primary ignition runs. Hantek HT201
A universal oscilloscope probe with a BNC connector and a 10:1 voltage divider. It has a frequency response of 60 MHz and allows measurements with a maximum voltage of up to 600 V. Hantek PP-80
Micsig MDP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 150 MHz and the ability to measure voltage up to 700 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig MDP701
BNC connector cable (adapter) for minigrabber clips. It enables the connection of the tested system with an oscilloscope
Universal oscilloscope probe with BNC connector. It has a voltage divider of 10:1 and offers a frequency response of 100 MHz. It allows measurements with a maximum voltage of up to 600 V. P6100