Step-Down Buck Voltage Regulator 3.3V 600mA D24V6F3
ID: 210798
zł29.53
Tax included
zł24.01 tax excl.
The Step-Down D24V6F3 Buck Voltage Regulator module gives the output voltage of 3.3V with a wide input voltage range of 4.8-42V and a maximum output current of 600 mA. Pololu 2106
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
The Step-Down D24V6F3 buck voltage regulator module has a 3.3 V output voltage with a wide input voltage range of 4.8-42V. The maximum current load of the module is 600 mA. The converter achieves a standard efficiency of 80 - 90% at similar values of input and output voltage.
Note! The board does not have reverse-voltage protection. Incorrect power connection will cause permanent damage of the module.
The inverter module is also available in other voltage variants with constant output voltage: 5 V, 9 V and 12 V.
Features
- Input voltage: 4.8-42 V
- 3.3 V output voltage with 4% accuracy
- Type. maximum current: 600 mA
- Built-in protection against short-circuit and overheating
- Type. efficiency: 80..90%
- Size: 13 × 10 × 3 mm
- Possibility of mounting goldpin
Connections
- VIN - power input (4.8-42V)
- GND - mass
- VOUT - output
- SHDN – Shutdown pin can be driven low (under 0.3 V) to turn off the output and put the board into a low-power state that typically draws 20 μA, and it can be driven high (above 2.3 V) to enable the board. If you do not need to use the shutdown feature, the SHDN pin can be directly connected to VIN to permanently enable the board. You should not leave this pin disconnected as this can result in unpredictable behavior.
Kit contains
- Buck converter module D24V6F3 x1
- Goldpin connector 4pin straight x1
- Goldpin connector 4pin right-angle x1
210798
Data sheet
- Output voltage
- 3,3 V
- Output current
- 0.6A
- Converter type
- Step-down
- Supply voltage min
- 4,8 V
- Supply voltages max
- 42 V
Other products in the same category (16)
This compact (0.4″ × 0.5″) switching step-down (or buck) voltage regulator takes input voltages up to 50 V and efficiently reduces them to 7.5 V while allowing for a maximum output current of 600 mA. It has a very low dropout, so it can be used with input voltages that are within a few hundred millivolts of its output.
zł33.31
24h
Available quantity: 1
Available
The compact (0.4″ × 0.5″) D24V5F5 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 5 V while allowing for a maximum output current of 500 mA. Pololu 2843
zł26.03
6 weeks
No product available!
Step-Down DC-DC converter module based on the D36V6F6 chip. Input voltage 6.2..50V, output voltage 6V (max. 600mA). Pololu 3793
zł35.13
24h
Available quantity: 2
Available
Step-Down converter module with input voltage from 4.75 to 23V, output voltage from 1 to 17V and output current 1.8 A (3 A instantaneous current).
zł7.70
24h
Available quantity: 73
Available
Step-Down converter with an output voltage of 5 V, input voltage from 4.5 to 40 V and a maximum current of 2 A. The board is equipped with a segment LED display and a USB output
zł18.61
24h
Available quantity: 12
Available
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 36V and efficiently reduces it to 5V. The board measures only 0.7″ × 0.7″ yet delivers a typical continuous output current of up to 2.5A and features reverse voltage protection. Pololu 2858
zł53.14
24h
Available quantity: 2
Available
Step-Down Voltage Regulator D24V25F5. Pololu 2850
zł77.03
24h
Available quantity: 2
Available
Available
Step-Down converter module with an input voltage of up to 5.5 V, an output voltage of 3.3 V and an output current of 1.2 A (2 A instantaneous current). Adafruit 4711
zł24.65
24h
Available quantity: 1
Available
VRM: Voltage Regulator Module (Rev. B) is a step-down converter based on the Texas Instruments TPS54620 chipset. Input voltage in the range 5 ... 15 V, output voltage 3.3 V or 5 V. Digilent 210-156
zł99.70
6 weeks
No product available!
Modular power supply with a power of 3 W, input voltage from 100 to 240 V and output voltage of 5 V. Designed for mounting on a PCB. Hi-Link HLK-PM01
zł17.20
6 weeks
No product available!
A power supply based on a DC-DC converter with a current capacity of up to 4 A. The input voltage can range from 5 V to 30 V, while the output voltage is adjustable from 0.5 V to 30 V. ZK-4KX
zł68.90
Delivery date unknown
No product available!
Step-Down converter D36V28F12 with an output voltage of 12 V, an input voltage from 12.9 to 50 V and a maximum output current of 3.3 A. Pololu 3786
zł90.98
24h
Available quantity: 2
Available
Step-Down RT8272 converter with adjustable output voltage in the range from 5 V to 12 V, input voltage from 5 to 24 V and a maximum output current of 3 A
zł10.33
24h
Available quantity: 19
Available
Step-Down XL4015 converter module with adjustable output voltage in the range from 1.25 to 36 V with a wide input voltage range from 4 to 38 V and a maximum output current of 5 A
zł9.59
24h
Available quantity: 221
Available
No product available!
The Step-Down D24V6F3 Buck Voltage Regulator module gives the output voltage of 3.3V with a wide input voltage range of 4.8-42V and a maximum output current of 600 mA. Pololu 2106