Main view
search
  • Main view
ID: 1186175
5906623423897
zł135.36
Tax included

zł110.05 tax excl.

Development kit with STM32F407IGT6 microcontroller. Requires external programmer with SWD or JTAG interface. Waveshare Core407I

24h
Available
Available quantity: 1
Kamami is the official distributor of Waveshare displays, accessories and modules.

Description

Development kit with a microcontroller from the STM32F407IG family (ARM Cortex-M4 core). It was equipped with the basic elements needed to start the system, configuration switches and a reset button. The user has at his disposal all the pins of the system led out to pin connectors with a pitch of 2.54 mm. It is powered via the miniUSB connector and programmed via the JTAG or SWD interface. There is no debugger on the board, therefore the set requires an external programmer / debugger. Full documentation is available on the product page.

  1. STM32F407IGT6 :the high performance STM32 MCU which features:
    • Core: Cortex-M4 32-bit RISC
    • Feature: a full set of single-cycle DSP instructions
    • Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
    • Operating Voltage: 1.8V-3.6V
    • Package: LQFP176
    • Memories: 1024kB Flash, 192+4kB SRAM
    • MCU communication Interfaces:
      • 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C
      • 1 x FSMC, 1 x SDIO, 2 x CAN
      • 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
      • 1 x 10/100 Ethernet MAC
      • 1 x 8 to 12-bit parallel camera interface
    • AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
    • Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
  2. AMS1117-3.3 (on bottom side): 3.3V voltage regulator
  3. MIC2075 (on bottom side): onboard USB power management device
  4. Power supply switch, powered from 5Vin or USB connection
  5. Boot mode switch, for configuring BOOT0 pin
  6. Power indicator
  7. VBUS LED
  8. Reset button
  9. 8M crystal oscillator
  10. 32.768K crystal (on bottom side), for internal RTC with calibration
  11. JTAG/SWD interface: for debugging/programming
  12. USB connector, used for establishing USB communication between PC and the STM32 development board
  13. IO expander (including VCC/GND), all the MCU pins are accessible on expansion connectors for further expansion
  14. 5Vin pinheader, 5V power supply is required when using USB HOST/OTG
  15. USB jumper
    • short the jumper when using USB
    • open the jumper to disconnect from I/O ports
  16. VBAT selection jumper
    • short the jumper to use system power supply
    • open the jumper to connect the VBAT to external power, such as battery
  17. VREF selection jumper
    • short the jumper to connect VREF+/VREF- to VCC/GND
    • open the jumper to connect VREF+/VREF- to other custom pin via jumper wire

Features

  • STM32F407IG microcontroller
  • Configuration switches and jumpers
  • MiniUSB power connector
  • Power LED
  • SWD and JTAG interface
  • Reset button
  • 3.3 V regulator

Kit contains

  • Core407I
  • MiniUSB cable
1186175

Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20

Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20

You might also like

Other products in the same category (16)