Category: STARTER KITS, PROGRAMMERS, MODULES

Vibrating sensor module, Plug & Play, omni-directional, designed for switching over low-current circuits. DFRobot DFR0027

MicroMod main module with RP2040 microcontroller. Equipped with an M.2 connector, it can work with MicroMod expansion boards. SprakFun DEV-17720

MicroMod main module with nRF52840 chip equipped with Bluetooth 5.1. The board uses an M.2 connector, so it can work with MicroMod expansion boards. SprakFun DEV-16984

The DLight Unit module with the BH1750FVI-TR sensor enables digital illuminance measurement with high resolution and low power consumption. It is suitable for automation systems, measurement devices, and IoT projects requiring precise light detection. M5Stack U096

Non-contact liquid level sensor. It allows you to detect liquids without the need to immerse the sensor in the liquid. Digital output. DFRobot FIT0212

WiFi 802.11 b/g/n module with ESP8266 chip, there are 8 pins with UART and GPIO interface. Built-in PCB antenna. SparkFun WRL-17146

Freescale starter kit with Kinetis KL25Z family microcontroller (Cortex-M0 +), integrated with the programmer-debugger OpenSDA, capacitive switch, LED-RGB and MEMS 3D accelerometer. Arduino-compatible outputs.

Adapter with micro SD card slot. It is equipped with connectors compatible with Teensy LC, 3.0, 3.1, 3.2, 3.5 and 3.6 boards and WIZ820io or WIZ850io Ethernet modules. WIZ820-SD-ADAPTOR

Module with 12-channel MPR121 capacitive touch sensor. The board is equipped with a Stemma QT connector and communicates via the I2C interface. Adafruit 4830

The expansion module is designed to work with Raspberry Pi 400 - a  portable computer built into the keyboard. The board has a 40-pin connector in the pin position and two Qwiic connectors. SparkFun DEV-17512

Module with black and white OLED display, 0.96" diagonal and 128x64 px resolution. Equipped with STEMMA QT connector, communicates via I2C or SPI interface. Adafruit 326

Adafruit 640 - Stainless Thin Conductive Thread - 2 ply - 23 meter/76 ft

TPL5110 external counter module to turn on a project after a set time and save energy. The TPL5110\'s delay is configurable with resistors ranging from 100 ms to two hours. SparkFun PRT-15353

Ultrasonic distance sensor with a range of up to 5 m with an analog output The module is supplied with the voltage from 3.3 to 5.5 V. DFRobot SEN0307

Module with an analog TEMT6000 light intensity sensor. The voltage at the output is linearly correlated with the intensity of the incident light. The module is supplied with the voltage from 3.3 to 5V. DFRobot SEN0043

8x16 LED matrix equipped with colored LEDs and a driver. It is powered by 5 V and communicates via the I2C interface (Gravity connector). DFRobot DFR0522

Module with an analog MQ7 carbon monoxide sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0132

This development board combines Wi-Fi, Bluetooth, and LoRa technologies, ideal for IoT projects requiring long-range communication. Equipped with a dual-core 240 MHz processor and an 868 MHz SX1262 modem, it provides a transmission range of up to several kilometers with low power consumption. It features a built-in 0.96-inch OLED display, a CP2102 USB-to-UART converter, and a lithium battery charging circuit for mobile operation. Heltec Lora32-V3

K8048 is a prototyping kit and PIC programmer, enabling testing and programming of various Microchip microcontrollers. Thanks to its extended functions and RS232 support, it is suitable for education, prototyping, and hobby electronic projects.

Module with a temperature and humidity sensor DHT22. It allows you to measure humidity in the range from 0 to 100% and temperature from -40 to 80℃. DFRobot SEN0137