Category: STARTER KITS, PROGRAMMERS, MODULES

Espressif ESP32-C6 WiFi module board with RISC-V core. It offers 4 MB Flash and 512 KB SRAM and RGB diode. It has a built-in ceramic WiFi/BLE antenna. Waveshare ESP32-C6-Zero

The development board allows you to easily use the capabilities of ESP32 (Wi-Fi + Bluetooth BLE) from Espressif. There is a USB / UART converter on the board, and most of the GPIO line of the ESP-WROOM-32D module has been connected to pins with a pitch of 2.54mm. ESP32-DevKitC V4

RJ12 6-Pin PH 10-Pin IDC Adapter for PIC Microcontrollers Programming

Simulation set for Siemens S7-1200 PLC devices. Using this set, it is possible to verify the operation of a program written for a PLC by applying the appropriate states to the digital inputs, to the analogue (ADC) inputs voltages from the built-in or external sensors. LED status monitoring is possible

The KAmod BlackPill 401 is an evaluation board with an STM32F401CCU microcontroller, featuring USB-C with ESD protection and a modified power circuit. With a pre-installed bootloader, it supports Arduino IDE, offering 32 GPIOs and versatile programming capabilities

The KAmod BlackPill 411 is an evaluation board featuring the STM32F411CEU microcontroller, offering versatile programming capabilities with a USB-C connector and a pre-installed bootloader compatible with Arduino IDE. Equipped with 32 GPIOs, a modified power circuit, and ESD protection, it is perfect for embedded projects.

A small DIP adapter with a 2.54 mm goldpin connector. Designed for the ESP-01 and ESP-01S modules

The KAmod BlackPill 411 is an evaluation board featuring the STM32F411CEU microcontroller, offering versatile programming and communication capabilities via USB-C. Compatible with the BlackPill project, it stands out with a modified power circuit, ESD protection, and a pre-installed bootloader for Arduino IDE support. With 32 GPIO pins, an SWD interface, and RTC support, it is an ideal solution for various embedded projects

Four relay output module for Raspberry Pi 4B, Pi 3B+ Pi3B, Pi2, Pi+, Pi minicomputers.

WiFi module based on ESP8266. The module has a built-in antenna and USB-UART converter. The module can be programmed in Lua (under the control of the NodeMCU firmware) or in the Arduino environment. 10 GPIO lines are available which each can be configured to work as PWM, I2C.

Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.

The STM32 Nucleo-64 boards provide an affordable and flexible way for users to try out new concepts and build prototypes with the STM32 microcontrollers, choosing from various combinations of performance, power consumption and features

A powerful development board based on the ESP32-S3-WROOM-1 microcontroller, offering a dual-core Xtensa LX7 processor with a frequency of up to 240 MHz, which enables support for advanced AIoT and IoT applications. The board is equipped with 16MB Flash and 8MB PSRAM, which allows for storing larger applications and efficient real-time data processing. With built-in 2.4GHz Wi-Fi, Bluetooth 5.0 LE and easy connection via USB-C, it is an ideal solution for the development of smart devices, sensors and automation systems. Waveshare ESP32-S3-DEV-KIT-N16R8-M

Development kit with STM32L496ZGT6 microcontroller with built-in ST-Link programmer. Extensive equipment, including: MEMS 6DoF sensor, motor controller, joystick, LED display, 8 LED diodes, RGB LED, audio amplifier, Flash memory QSPI 1 MB, microphone.

A small module matching the contact plate based on a 32-bit microcontroller with ARM Cortex M7 core. Has a microSD slot. PJRC TEENSY41

STM32 Nucleo-144 development board with STM32F767ZI MCU, supports Arduino, ST Zio and morpho connectivity

The KAmod ESP32-C3 board, equipped with a RISC-V microcontroller and a set of MEMS and SHTC3 sensors, enables the creation of IoT, measurement, and control applications. Thanks to power from USB-C or a battery and support for Arduino and Rust, it works perfectly in mobile projects and embedded systems.

ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 microcontrollers

Development board D1 Mini V3 with WiFi module ESP-8266 and 4 MB Flash memory. The module can be programmed from the Arduino IDE level. WeMos D1 Mini V3.x

Cable that allows you to attach the ATMEL-ICE programmer to the development kit with any connector (supported by the programmer), via single pin plugs (goldpin)